Document Number:
NL IEC 60598 2 24 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
25000.0000
This part of the IEC 60598 series specifies requirements for luminaires intended for use where the necessity of limited temperature on the outer surface exists, due to the risk of thermal effects, combustion or degradation of materials but where the risk of explosion in the atmosphere does not exist. The luminaires are for use with electric light sources on supply voltages not exceeding 1 000 V. This standard specifically excludes requirements for luminaires for use in explosive gas atmospheres and explosive dust atmospheres
Document Number:
NL IEC 60598 2 25 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
This section of IEC 598-2 details specific requirements for luminaires for use with tungsten filament, fluorescent and other discharge lamps on supply voltages not exceeding 1 000 V for use in clinical areas in which medical treatment, examination and medical care takes place in hospitals and health care buildings. This standard does not apply to medical electrical equipment, as defined in 2.2.15 of IEC 601-1, containing a light source. NOTE 1 – Subclause 2.2.15 of IEC 601-1 states: Electrical equipment, provided with not more than one connection to a particular supply mains and intended to diagnose, treat, or monitor the patient under medical supervision and which makes physical or electrical contact with the patient and/or transfers energy to or from the patient and/or detects such energy transfer to or from the patient. This standard does not apply to luminaires for emergency lighting and luminaires for general illumination in non-clinical areas (e.g. offices). NOTE 2 – For these luminaire types, reference should be made to other sections of IEC 598-2. This standard does not apply to luminaires or parts of luminaires which are designed to be sterilized by the autoclave process and luminaires for operating tables.
Document Number:
NL IEC 60715 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
This document specifies dimensional and functional requirements for the compatible mounting of switchgear, controlgear and accessories on some types of rails. The object of this document is to specify those dimensions that are critical for the correct design of mounting rails and equipment. The following sections are covered by this document: – "top hat" section; – "C" section; – "G" section. NOTE 1 Mounting compatibility does not imply functional interchangeability. Annexes deal with specific steel mounting rails satisfying the requirements of this document, and give additional dimensional data and loading requirements applicable to such rails. NOTE 2 The detailed design and material of specific steel rails is given in the annexes. NOTE 3 Other shapes of rails complying with this document not listed in Annex A can be used. Mounting rails used as a protective conductor using a conducting connection to a protective conductor terminal block are specified in IEC 60947-7-2. In other applications where the mounting rail is used as earthing conductor, the relevant product standard applies. This document has the status of a horizontal standard in accordance with IEC Guide 108:2006. This horizontal standard is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 108. One of the responsibilities of a technical committee is, wherever applicable, to make use of horizontal standards in the preparation of its publications. The contents of this horizontal standard will not apply unless specifically referred to or included in the relevant publications.
Document Number:
NL IEC 60865 1 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 60865-1:2011 is applicable to the mechanical and thermal effects of short-circuit currents. It contains procedures for the calculation of: the electromagnetic effect on rigid conductors and flexible conductors, the thermal effect on bare conductors. For cables and insulated conductors, reference is made, for example, to IEC 60949 and IEC 60986. For the electromagnetic and thermal effects in d.c. auxiliary installations of power plants and substations reference is made to IEC 61660-2. Only a.c. systems are dealt with in this standard. This third edition cancels and replaces the second edition published in 1993 and constitutes a technical revision. The main changes with respect to the previous edition are: - The determinations for automatic reclosure together with rigid conductors have been revised. - The influence of mid-span droppers to the span has been included. For vertical cable-connection the displacement and the tensile force onto the lower fixing point may now be calculated. Additional recommendations for foundation loads due to tensile forces have been added. The subclause for determination of the thermal equivalent short-circuits current has been deleted (it is now part of IEC 60909-0). The regulations for thermal effects of electrical equipment have been deleted. The standard has been reorganized and some of the symbols have been changed to follow the conceptual characteristic of international standards.
Document Number:
NL IEC 60865 2 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC TR 60865-2:2015(E) shows the application of procedures for the calculation of mechanical and thermal effects due to short circuits as presented in IEC 60865-1. This technical report is an addition to IEC 60865-1. It does not, however, change the basis for standardized procedures given in that publication. This second edition cancels and replaces the first edition published in 1994 and constitutes a technical revision. It includes the following changes. The determinations for auto reclosure together with rigid conductors have been revised. The configurations in cases of flexible conductor arrangements have been changed. The influence of mid-span droppers to the span has been included. For vertical cable-connection the displacement and the tensile force onto the lower fixing point may be calculated now. Additional recommendations for foundation loads due to tensile forces have been added. The subclause for determination of the thermal equivalent short-circuits current has been deleted (is part of IEC 60909-0:2001 now). The standard IEC 60865-1:2011 has been reorganized and some of the symbols have been changed to follow the conceptual characteristic of international standards
Document Number:
NL IEC 60882 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
25000.0000
States basic technical requirements for cathode heating of tubular fluorescent lamps having pre-heated cathodes and intended for use in starterless circuits at a frequency of 50 Hz or 60 Hz. The requirements presented are those needed, as far as cathode heating conditions are concerned, to obtain reliable lamp performance. Ballasts used for the operation of these lamps should supply cathode heating voltages and currents in accordance with these basic requirements. This publication has the status of a report.
Document Number:
NL IEC 60909 0 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 60909-0:2016 is applicable to the calculation of short-circuit currents in low-voltage three-phase AC systems, and in high-voltage three-phase AC systems, operating at a nominal frequency of 50 Hz or 60 Hz. It establishes a general, practicable and concise procedure leading to results which are generally of acceptable accuracy and deals with the calculation of short-circuit currents in the case of balanced or unbalanced short circuits. This second edition cancels and replaces the first edition published in 2001. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - contribution of windpower station units to the short-circuit current; - contribution of power station units with ful size converters to the short-circuit current; - new document structure. This publication is to be read in conjunction with IEC TR 60909-1:2002, IEC TR 60909-2:2008, IEC 60909-3:2009 and IEC TR 60909-4:2000. Show less
Document Number:
NL IEC 60909 1 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
EasyPower offers a complete and accurate solution to short-circuit calculations in three-phase AC systems using the IEC-60909 standard. You can enter equipment data and parameters via user friendly interface. The results meet requirements of IEC-60909 and match the example provided in IEC TR 60909-4 section 6. The IEC standard terminology is used in the user interface and reports. EasyPower supports the following four types of short-circuit conditions as per IEC 60909: *3-phase short circuit *Line-to-line short circuit *Line-to-line short circuit with earth connection (double line-to-earth) *Line-to-earth short circuit
Document Number:
NL IEC 60909 2 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 60909-2:2008(E) comprises data of electrical equipment collected from different countries to be used when necessary for the calculation of short-circuit currents in accordance with IEC 60909-0. It may be applied for calculating short-circuit currents in low-voltage networks if they are in accordance with typical equipment employed in the user's country. The collected data and their evaluation may be used for medium- or high-voltage planning purposes and also for comparison with data given by manufacturers or electricity suppliers. For overhead lines and cables the electrical data may in some cases also be calculated from the physical dimensions and the material following the equations given in this report. This second edition cancels and replaces the first edition published in 1992 and constitutes a technical revision. The significant technical changes with respect to the previous edition are as follows: - Subclause 2.5 gives equations and examples for the calculation of the positive-, the negative- and the zero-sequence impedances and reduction factors for high-, medium and low-voltage cables with sheaths and shields earthed at both ends. - Subclause 2.7 gives equations and figures for the calculation of the positive -sequence impedances of busbar configurations
Document Number:
NL IEC 60909 3 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 60909-3:2009 RLV contains the International Standard and its Redline version. The Redline version provides you with a quick and easy way to compare all the changes between this standard and its previous edition. The Redline version is not an official IEC Standard, only the current version of the standard is to be considered the official document. IEC 60909-3:2009 specifies procedures for calculation of the prospective short-circuit currents with an unbalanced short circuit in high-voltage three-phase a.c. systems operating at nominal frequency 50 Hz or 60 Hz, i. e.: - currents during two separate simultaneous line-to-earth short circuits in isolated neutral or resonant earthed neutral systems; - partial short-circuit currents flowing through earth in case of single line-to-earth short circuit in solidly earthed or low-impedance earthed neutral systems. The currents calculated by these procedures are used when determining induced voltages or touch or step voltages and rise of earth potential at a station (power station or substation) and the towers of overhead lines. Procedures are given for the calculation of reduction factors of overhead lines with one or two earth wires. This edition constitutes a technical revision. The main changes with respect to the previous edition are: - New procedures are introduced for the calculation of reduction factors of the sheaths or shields and in addition the current distribution through earth and the sheaths or shields of three-core cables or of three single-core cables with metallic non-magnetic sheaths or shields earthed at both ends; - The information for the calculation of the reduction factor of overhead lines with earth wires are corrected and given in the new Clause 7; - A new Clause 8 is introduced for the calculation of current distribution and reduction factor of three-core cables with metallic sheath or shield earthed at both ends; - The new Annexes C and D provide examples for the calculation of reduction factors and current distribution in case of cables with metallic sheath and shield earthed at both ends.
Document Number:
NL IEC 61347 2 3 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 61347-2-3:2011 specifies particular safety requirements for electronic control gear for use on a.c. and d.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with fluorescent lamps as specified in IEC 60081 and IEC 60901, and other fluorescent lamps for high-frequency operation. This second edition cancels and replaces the first edition published in 2000, its Amendment 1 (2004) and its Amendment 2 (2006), IEC 61347-2-4 published in 2000, IEC 61347-2-5 published in 2000 and IEC 61347-2-6 published in 2000. This second edition constitutes a technical revision. The significant revisions with respect to the first edition are: - rectifying test conditions when dimming; - construction requirements; - measurement circuits and limits for HF leakage currents; - modification of the structure to become a standard exclusively for a.c. and d.c. central supplied electronic control gear for general lighting and Annex J cover c
Document Number:
NL IEC 60099 4 : 2006
Sector:
Construction Materials and Building
Status:
C
Production Year:
2006
Price:
50000.0000
This part of IEC 60099 applies to non-linear metal-oxide resistor type surge arresters without spark gaps designed to limit voltage surges on a.c. power circuits with Us above 1 kV.
Document Number:
NL IEC 60099 5 : 2006
Sector:
Construction Materials and Building
Status:
C
Production Year:
2006
Price:
50000.0000
This part of IEC 60099 provides information, guidance, and recommendations for the selection and application of surge arresters to be used in threephase systems with nominal voltages above 1 kV. It applies to gapless metal-oxide surge arresters as defined in IEC 60099-4, to surge arresters containing both series and parallel gapped structure – rated 52 kV and less as defined in IEC 60099-6 and metal-oxide surge arresters with external series gap for overhead transmission and distribution lines (EGLA) as defined in IEC 60099-8. In Annex J, some aspects regarding the old type of SiC gapped arresters are discussed. Surge arrester residual voltage is a major parameter to which most users have paid a lot of attention to when selecting the type and rating. Typical maximum residual voltages are given in Annex F. It is likely, however, that for some systems, or in some countries, the requirements on system reliability and design are sufficiently uniform, so that the recommendations of the present standard may lead to the definition of narrow ranges of arresters. The user of surge arresters will, in that case, not be required to apply the whole process introduced here to any new installation and the selection of characteristics resulting from prior practice may be continued. Annexes H and I present comparisons and calculations between old line discharge classification and new charge classification.
Document Number:
NL IEC 60099 1 : 2006
Sector:
Construction Materials and Building
Status:
C
Production Year:
2006
Price:
50000.0000
La présente partie de la Norme internationale CEI 60099 s'applique aux appareils de protection contre les surtensions prévus pour un fonctionnement répété et conçus pour limiter les surtensions sur les circuits alternatifs et interrompre le courant de suite. Elle s'applique particulièrement aux parafoudres comportant un éclateur simple ou multiple en série avec une ou plusieurs résistances variabl
Document Number:
NL IEC 60364 1 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
IEC 60364-1 gives the rules for the design, erection, and verification of electrical installations. The rules are intended to provide for the safety of persons, livestock and property against dangers and damage which may arise in the reasonable use of electrical installations and to provide for the proper functioning of those installations.
Document Number:
NL IEC 60364 3 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
Includes the following: purposes, supplies and structures (gives descriptions of TN, TT and IT distribution systems and system earthing); classification of external influences; compatibility; maintainablility; safety services
Document Number:
NL IEC 60410 : 2006
Sector:
Sociology. Services. Company Organization and Mana
Status:
C
Production Year:
2006
Price:
50000.0000
This recommendation establishes sampling plans and procedures for inspection by attributes. When specified by the responsible authority, this recommendation shall be called up in the specification, contract, inspection instructions or other documents and the provisions set forth herein shall govern. The "responsible authority" shall be designated in one of the above documents. Note: The responsible authority may be the customer
Document Number:
NL IEC 60755 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 60775:2017(E) provides general minimum requirements, recommendations and information for the drafting of standards on residual current operated protective devices (hereinafter referred to as residual current devices, "RCDs"). It applies to any device providing residual current protection intended primarily for protection against electric shock hazard. This first edition cancels and replaces IEC TR 60755 published in 2008 and constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC TR 60755: a. restructuration of the document, as a Group Safety Publication, in compliance with Guide 104; b. introduction of classification for type F RCDs; c. introduction of Clause 9 for tests of RCDs (operating characteristics, electrical endurance, behaviour in short-circuit conditions, trip-free mechanism, test device, surges, reliability, EMC). It has the status of a group safety publication in accordance with IEC Guide 104.
Document Number:
NL IEC 60781 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
This application guide presents a practical method to be used when calculating short-circuit currents in low-voltage networks. The method corresponds strictly with IEC 60909 and leads to conservative results with sufficient accuracy. Two short-circuit currents which differ in magnitude are to be calculated: -the maximum short-circuit current which causes the maximum thermal and electromagnetic effects on electrical equipment and determines the required capacity or rating; -the minimum short-circuit current which may be a basis for the adjustment of protective devices
Document Number:
NL IEC 61196 2 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
Prescribes recommended ratings and characteristics. Selects from the generic specification the appropriate quality assessment procedures, test and measuring methods. Gives general performance requirements for semi-rigid coaxial cables plus complementry test methods.
Document Number:
NL IEC 61196 3 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
Prescribes recommended ratings and characteristics and selects from the generic specification the appropriate quality assessment procedures, test and measuring methods, and gives general performance requirements for coaxial cables for local area networks plus complementary test methods. Test severities and requirements prescribed in detail specifications referring to this sectional specification should be of equal or higher performance levels. When the requirements of IEC 61196-1 and of this sectional specification conflict with each other, this sectional specification shall prevail.
Document Number:
NL IEC 61196 4 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
IEC 61196-4:2015(E) applies to radiating coaxial communication cables. These cables are intended for use in wireless communication systems, such as tunnels, railways, highways, subways, elevators and other installations in which conventional antenna transmission is not satisfactory or even impossible. This third edition cancels and replaces the second edition published in 2004. This edition constitutes a technical revision. The main changes with respect to the previous edition are as follows: - a definition for coupling loss was added, - Clause 4 "Materials and cable construction" was added, - rated temperature range, operating frequency and radiating characteristics as standard rating and characteristics were added, - identification, marking and labeling was added, - the tables of test procedures were revised, - quality assessment and packaging was added, - Annex C, "Coupling loss around circumferential orientation of radiating cable" was added, - Annex D "Radiating intensity around circumferential orientation of radiating cable" was added. This publication is to be read in conjunction with IEC 61196-1:2005.
Document Number:
NL IEC 60127 5 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
25000.0000
This part of IEC 60127 gives a guide for tests for assessing the quality of miniature fuse-links other than type tests, for the case where there is no complete agreement between the user and the manufacturer on what such tests apply. This document provides guidelines and limits generally acceptable for quality control purposes by large scale users and manufacturers of miniature fuse-links. This document has validity for large scale series with lot sizes of 10 000 and more. It is also applicable for smaller lot sizes, if necessary. Periodic inspections by reduced type tests (Clause 5) are intended to be carried out periodically in order to ensure that the level of technical performance previously verified by complete type tests as given in subsequent parts of the IEC 60127 series is maintained. The frequency of periodic in relation to lot-by-lot inspections is not established in this document
Document Number:
NL IEC 60127 6 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
This part of IEC 60127 is applicable to fuse-holders for miniature cartridge fuse-links according to IEC 60127-2 and sub-miniature fuse-links according to IEC 60127-3 for the protection of electric appliances, electronic equipment and component parts thereof, normally intended for use indoors. Examples of fuse-holder types with different features are given in Table 1. Table 1 – Features of unexposed or exposed fuse-holders 1 Types of mounting 1.1 Panel and base mounting 1.2 Printed circuit board mounting 2 Methods of fastening 2.1 Methods of fastening on panel: 2.1.1 Fixing nut fastening (threaded nut) 2.1.2 Snap-in fastening: 2.1.2.1 Fuse-base with an integral spring system 2.1.2.2 Fuse-base with a separate spring-nut (a nut fabricated, e.g. from thin spring steel having an impression designed to accommodate the mating part) 2.2 Methods of fastening on printed circuit (PC) board: 2.2.1 Solder fastening 2.2.2 Plug-in fastening 3 Methods of insertion of the fuse-carrier into the fuse base 3.1 Screw insertion 3.2 Bayonet insertion 3.3 Plug-in insertion 4 Types of terminals 4.1 Screw terminals 4.2 Solder terminals 4.3 Quick connect terminals 4.4 Other solderless terminals: – crimp terminals – wire wrap terminals 5 Protection against electric shock 5.1 Fuse-holder without integral protection against electric shock 5.2 Fuse-holder with integral protection against electric shock 5.3 Fuse-holder with enhanced integral protection against electric shock NOTE This list is not intended to be comprehensive and fuse-holders which are not listed are not necessarily excluded from the scope. This part of IEC 60127 applies to fuse-holders with: This is a preview - click here to buy the full publication – 10 – IEC 60127-6:2014 IEC 2014 – a maximum rated current of 16 A; and – a maximum rated voltage of 1 500 V d.c. or 1 000 V a.c.; and – for use up to 2 000 m above sea-level, unless otherwise specified. The object of this standard is to establish uniform requirements for safety and the assessment of electrical, mechanical, thermal and climatic properties of fuse-holders and the compatibility between fuse-holders and fuse-links.
Document Number:
NL IEC 60127 10 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
Relates to miniature fuses for the protection of electric appliances, electronic equipment and component parts thereof, normally intended to be used indoors, as specified in IEC 60127-2, 60127-3 and 60127-4. It relates to fuse-holders for miniature fuse-links according to IEC 60127-6. The object of this guide is to introduce the user to the important properties of miniature fuse-links and fuse-holders for miniature fuses-links and to give some guidance on applying them
Document Number:
NL prCEN ISO TS 15874 7 : 2006
Sector:
Construction Materials and Building
Status:
C
Production Year:
2006
Price:
25000.0000
This document gives requirements and guidance for the assessment of conformity of compounds, products, and assemblies in accordance with the applicable part(s) of ISO 15874 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures. NOTE In order to help the reader, a basic test matrix is given in Annex A. In conjunction with the other parts of ISO 15874 (see Foreword), this document is applicable to polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 15874-1:2013, Table 1).
Document Number:
NL IEC 61347 2 4 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
25000.0000
This part of IEC 61347 specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from transient and surge-free power sources, operated directly from batteries without charging equipment as used in leisure equipment, for example, caravans, etc. This first edition of IEC 61347-2-4, together with IEC 61347-1, cancels and replaces section three of the first edition of IEC 60924, published in 1990, and constitutes a minor revision. This standard shall be used in conjunction with IEC 61347-1. It was established on the basis of the first edition (2000) of that standard
Document Number:
NL IEC 61347 2 5 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
This part of IEC 61347 specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from power sources likely to have attendant transients and surges, for example, for road and railway vehicles, tramcars, and craft used for public transport. This first edition of IEC 61347-2-5, together with IEC 61347-1, cancels and replaces section four of the first edition of IEC 60924, published in 1990, and constitutes a minor revision. This standard shall be used in conjunction with IEC 61347-1. It was established on the basis of the first edition (2000) of that standard.
Document Number:
NL IEC 61347 2 7 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
IEC 61347-2-7:2011 specifies particular safety requirements for battery supplied electronic controlgear for maintained and non-maintained emergency lighting purposes. It includes specific requirements for electronic controlgear and control units for self-contained luminaires for emergency lighting as specified by IEC 60598-2-22. This third edition cancels and replaces the second edition published in 2006. It constitutes a technical revision. Significant changes introduced into this third edition include: - modification of IEC 61347-2-7 to become a standard exclusively for d.c. battery supplied electronic controlgear for emergency lighting (self-contained) IEC 61347-2-3 Annex J is intended to cover centrally supplied emergency controlgear; - update of Clause 22 - Recharging devices; - modification of Clause 20 battery voltage characterisation to support EBLF measurement. This to simplify and increase reproducibility of testing; - rationalisation of requirements between IEC 61347-2-7 and IEC 60598-2-22 requirements of IEC 60598-2-22 being transferred to IEC 61347-2-7. This publication is to be read in conjunction with IEC 61347-1:2007.
Document Number:
NL IEC 61960 1 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 62899-501-1:2019(E) specifies failure modes and mechanical stress test methods for the determination of reliability characteristics of bendable or flexible printed primary cells and secondary cells and batteries as defined in IEC 60050-482:2004, 482-01-01, IEC 60050‑482:2004, 482-01-02, IEC 60050-482:2004, 482-01-03, IEC 60050-482:2004, 482‑01-04 and IEC 60050-482:2004, 482-01-05, respectively. Important parameters and specifications for primary cells are mentioned in IEC 60086-1 and IEC 60086-2. IEC 61960-3, as well as IEC 61951-1 and IEC 61951-2 define performance tests, designations, markings, dimensions and other requirements for secondary single cells and batteries. IEC 62133-1 and IEC 62133-2 address general safety requirements of secondary cells and batteries.
Document Number:
NL IEC 61960 2 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 61690-2:2000 defines the syntax and semantics for EDIF Version 4 0 0. EDIF Version 4 0 0 addresses EDIF Level 0 and Level 1. EDIF Version 3 0 0 provides support for Connectivity and Schematics; EDIF Version 4 0 0 offers additional capability by providing support for the representation of Printed Circuit Boards (PCBs) and Multi-chip Modules (MCMs) including technology rules and assembly drawings
Document Number:
NL IEC 62040 1 1 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 62040-1:2017 EXV includes the provisions of the general rules dealt with in IEC 62477-1:2012. The Extended version is not an official IEC Standard. Only the current versions of the related standards are to be considered the official documents. The Extended version is available in English only. IEC 62040-1:2017 applies to movable, stationary, fixed or built-in UPS for use in low-voltage distribution systems and that are intended to be installed in an area accessible by an ordinary person or in a restricted access area as applicable, that deliver fixed frequency AC output voltage with port voltages not exceeding 1 000 V AC or 1 500 V DC and that include an energy storage device. It applies to pluggable and to permanently connected UPS, whether consisting of a system of interconnected units or of independent units, subject to installing, operating and maintaining the UPS in the manner prescribed by the manufacturer. This document specifies requirements to ensure safety for the ordinary person who comes into contact with the UPS and, where specifically stated, for the skilled person. The objective is to reduce risks of fire, electric shock, thermal, energy and mechanical hazards during use and operation and, where specifically stated, during service and maintenance. This product standard is harmonized with the applicable parts of group safety publication IEC 62477-1:2012 for power electronic converter systems and contains additional requirements relevant to UPS. This edition includes the following significant technical change with respect to the previous edition: the reference document has been changed from IEC 60950-1:2005 (safety for IT equipment) to IEC 62477-1 (group safety standard for power electronic converters).
Document Number:
NL IEC 62040 1 2 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 62040-2:2016 RLV contains both the official IEC International Standard and its Redline version. The Redline version is not an official document, it is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition. IEC 62040-2:2016 is a type test product standard for electromagnetic compatibility (EMC) and applies to movable, stationary, fixed or built-in, pluggable and permanently connected UPS for use in low-voltage distribution systems with an environment being either residential, commercial, light industrial or industrial, which deliver output voltage with port voltages not exceeding 1 500 V DC or 1 000 V AC and which include an energy storage device. This edition includes the following significant technical changes with respect to the previous edition: a) the inclusion of network port limits in Table 1, Table 2 and Annex C for the sake of consistency with other standards; b) a change of quasi-peak limit for category C3 UPS in Table 2 for the sake of consistency with other standards; c) a clarification in Table 4 about the performance criteria for immunity tests; d) a revision of some test configurations in Annex A. The contents of the interpretation sheet 1 of June 2018 have been included in this copy.
Document Number:
NL IEC 61558 2 8 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
IEC 61558-2-8:2010 deals with the safety of bell and chime transformers and power supply units incorporating bell and chime transformers. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1998. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office
Document Number:
NL IEC 61558 2 13 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
IEC 61558-2-13:2009 deals with the safety of auto transformers for general applications and power supply units incorporating auto transformers for general applications. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1999. It constitutes a technical revision. The main changes consist of updating this part in accordance with Part 1 (2005), and increasing the supply voltages up to 1 100 V to be in line with the standards of TC 14. This part has the status of a group safety publication in accordance with IEC Guide 104. This part is intended to be used in conjunction with the latest edition of IEC 61558-1 and its amendments. It is based on the second edition (2005) of that standard. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.
Document Number:
NL IEC 61558 2 15 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
IEC 61558-2-15:2011 deals with safety aspects of isolating transformers for the supply of medical locations. This second edition cancels and replaces the first edition published in 1999. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104:2010. The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 2 months from the date of publication.
Document Number:
NL IEC 61558 2 17 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
This part 2 of IEC 61558 applies to associated power transformers for switch mode power supplies, single-phase or polyphase, air-cooled: separating transformers; isolating transformers; safety isolating transformers, 10 kVA for single-phase transformers; 16 kVA for polyphase transformers. This standard is applicable to dry type transformers. The windings may be encapsulated or non-encapsulated. It has the status of a group safety publication in accordance with IEC Guide 104 This part 2 supplements or modifies the corresponding clauses in IEC 61558-1
Document Number:
NL IEC 61558 2 23 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
50000.0000
IEC 61558-2-23:2010 deals with the safety of transformers for construction sites and power supply units incorporating transformers for construction sites. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 2000. It constitutes a technical revision. The main changes consist of updating this Part 2-23 in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104: The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office
Document Number:
NL IEC 61558 2 3 : 2006
Sector:
Electrical Engineering
Status:
C
Production Year:
2006
Price:
35000.0000
IEC 61558-2-3:2010 deals with the safety of ignition transformers for gas and oil burners. Ignition transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 1999. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office
Document Number:
NL EN 297 : 2005
Sector:
Mechanical Systems and Components for General Use
Status:
C
Production Year:
2005
Price:
50000.0000
This standard specifies the requirements and test methods for the construction, safety, fitness for purpose, rational use of energy, classification and marking of gas-fired central heating boilers. This standard applies to type B11 and B11BS boilers. This standard only covers type testing
Document Number:
NL 101 : 2005
Sector:
Food Technology
Status:
C
Production Year:
2005
Price:
25000.0000
تهدف هذه المواصفة القياسية إلى تحديد المتطلبات والشروط الواجب توافرها في هريس التفاح المعلّب المعد للاستهلاك المباشر.
Document Number:
NL 549 : 2005
Sector:
Food Technology
Status:
C
Production Year:
2005
Price:
25000.0000
تهدف هذه المواصفة القياسية اللبنانية الى تحديد التعاريف الخاصة بالعوامل الفزيقية التي تستخدم عادة في التخزين المبرد للفاكهة والخضار (الحرارة – الرطوبة النسبية – نسبة سريان الهواء – معدل تغيير الهواء...)، والقياسات الخاصة بهذه العوامل
Document Number:
NL 546 : 2005
Sector:
Food Technology
Status:
C
Production Year:
2005
Price:
15000.0000
تحدد هذه المواصفة القياسية المتطلبات والخصائص الواجب توافرها في خليط التوابل والبهارات المعدة للاستهلاك المباشر
Document Number:
NL EN 303 1 : 2005
Sector:
Mechanical Systems and Components for General Use
Status:
C
Production Year:
2005
Price:
25000.0000
This standard is applicable to heating boilers with burners using fans up to a normal heat output of 1000 kw they are operated either with negative pressure (natural draught boiler) or with positivepressure (pressurized boiler) in the combustion chamber, in accordance with the boiler manufacturer’s instructions. This standard specifies the necessary terminology, the requirements on the materials and testing of them , and marking requirements for heating boilers. Particular requirements for boilers which can be used with open vented systems are contained in prEN 303-4. The requirements of this standard apply to heating boiliers which are tested on an authorized test rig. Boilers in accordance with this standard are designed for the heating of central heating installations in which the heat carrier is water and the maximum alloqable operating temperature of which is restricted to 100 0 c. The maximum allowable operating pressure is 8 bar. For boilers with a built-in or attached water heater (storage or continuous flow heater ) this standard onlyapplies to the parts of the water heater which are necessarlly subject to the operating conditions of the heating boiler ( heating part ). This standard does not apply to gas boilers with atmospheric burners , boilers for solid fuels, oil or gas fired condensation boilers, bollers with oil vaporization burnes and low temperature boilers, for these bollers there are further requirements. NOTE : low temperature boillers are those operating with a (water) variable temperature up to 40 c or less , or those which cannot be set at a temperature higher than 550c .
Document Number:
NL EN 303 2 : 2005
Sector:
Mechanical Systems and Components for General Use
Status:
C
Production Year:
2005
Price:
25000.0000
This standard is applicable to heating boilers in accordance with prEN 303-1 up to a normal heat putput . of 1000 kw and prEN 303-4 up to a nominal heat output of 70 kw with atomizing oil burneers in accordance with en 267 which are designed for operating with liquid fuels . The requirements of this standard apply to type testing of heating boilers which are tested on a test rig in accordance with the test code given in EN 304 . the standard specifies the necessary heating technical requirements for heating boilers with liquid fuels. NOTE this standard can also be used as the basis for evaluation of pachage boiler burner units .
Document Number:
NL 663 1 : 2005
Sector:
Mechanical Systems and Components for General Use
Status:
C
Production Year:
2005
Price:
35000.0000
This Lebanese Standard applies to approval of containers of motor vehicles using liquefied petroleum gases in their propulsion system.
Document Number:
NL EN 933 4 : 2005
Sector:
Construction Materials and Building
Status:
C
Production Year:
2005
Price:
25000.0000
This standard describes the reference method used for type testing in cases of dispute, for the determination of the shape index of coarse aggregates. For other purposes, in particular factory production control, other methods may be used provided an appropriate working relationship with the reference method has been established. The test method specified in this European Standard is applicable to particle size fractions di/Di where Di ≤ 63 mm and di ≥ 4 mm.
Document Number:
NL EN 934 6 : 2005
Sector:
Construction Materials and Building
Status:
C
Production Year:
2005
Price:
25000.0000
This document specifies the procedures for sampling and for the assessment and verification of the constancy of performance (AVCP) for admixtures covered by the series EN 934
Document Number:
NL EN 933 1 : 2005
Sector:
Construction Materials and Building
Status:
C
Production Year:
2005
Price:
25000.0000
This European Standard describes the reference washing and dry sieving method used for type testing and in case of dispute, for determination of the particle size distribution of aggregates. For other purposes, in particular factory production control, other methods may be used, provided that an appropriate working relationship with the reference method has been established. It applies to all aggregates, including lightweight aggregates, up to 90 mm nominal size, but excluding filler. NOTE 1 The determination of the grading of fillers is specified in EN 933-10 Assessment of fines — Grading of filler aggregates (air jet sieving). NOTE 2 Dry sieving without washing may be used for aggregates free from particles which cause agglomeration.
Document Number:
NL EN 933 2 : 2005
Sector:
Construction Materials and Building
Status:
C
Production Year:
2005
Price:
15000.0000
This Part of this European Standard specifies nominal aperture sizes and shape for woven wire cloth and perforated plate in test sieves used for test methods for aggregates. It applies to aggregates of natural or artificial origin including lightweight aggregates.