Libnor | Catalogs |

Document Number: NL EN 747 1 : 2018

ISO 17743:2016 establishes a methodological framework that applies to the calculation and reporting of energy savings from existing (implemented) and prospective measures and actions which intend to save energy. This framework standard will be applicable to other standards in the field of energy saving determination. ISO 17743:2016 addresses the following in the context of energy savings: - terminology; - definition of the system boundaries; - principles for the determination of a baseline; - principles for statistical indicator-based methods; - data used; - principles for reporting. The development of the methodology for measurement and verification of the energy savings is not in the scope of this International Standard. The methodology of construction of the scenarios for future energy saving measures and actions is not in the scope of this International Standard.

Furniture - Bunk beds and high beds - Part 1: Safety, strength and durability requirements

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL EN 747 2 : 2018

This European Standard specifies requirements for the safety, strength and durability of bunk beds and high beds for domestic and non-domestic use. It applies to bunk beds with a height to the upper surface of the top bed base of 600 mm or more above the floor and to high beds with a height to the upper surface of the bed base of 600 mm or more above the floor. The loads and forces in the strength and durability tests apply to beds with an internal length greater than 140 cm and a maximum bed base width of 120 cm." The dimensional requirements are intended to minimise the risk of accidents, particularly to children. The strength and durability requirements are intended to represent use by one occupant per bed. Safety requirements for other products included in a bunk bed/high bed, for example a table or storage furniture, are not included in this standard. This European Standard does not apply to bunk beds and high beds used for special purposes, including but not limited to prison, the military and fire brigades.

Furniture - Bunk beds and high beds - Part 2: Test methods

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT.

Document Number: NL EN 1725 : 2018

This European Standard specifies test methods for the safety, strength and durability of bunk beds and high beds for domestic and non-domestic use. The loads and forces in the strength and durability tests apply to beds with an internal length greater than 140 cm and a maximum bed base width of 120 cm. The tests are designed to be applied to a bed that is fully assembled and ready for use. The applicable safety requirements are given in EN 747-1.

Domestic furniture-Beds and mattresses-Safety requirements and test methods

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT.

Document Number: NL CEN TR 16982 : 2018

This draft European Standard specifies mechanical safety requirements and testing for all types of fully erected domestic adult beds including all component elements such as bed frame, bed base, mattress and mattress pads (when they form a unit with the mattress). It does not applay to foldaway beds, bunk beds, children cots and adjustable beds for disabled persons where separate standards exist, as well as waterbeds and air beds. Further tests may be applicable for test units that are multi purposes, e.g. convertible sofa beds and power driven system.

Diesel Blends and Fuels - Cold Filterability Issues

Document Number: NL ISO 14631 : 2018

This Technical Report provides the latest thinking described during a workshop on 1 June 2015 by national experts involved in the investigations, and proposes possible solutions to solve the diesel fuel filter plugging issues in these countries. NOTE For the purposes of this Technical Report, the terms "% (m/m)" and "% (V/V)" are used to represent respectively the mass fraction, µ, and the volume fraction, φ.

Extruded Sheets of Impact-Modified Polystyrene (PS-I) — Requirements and Test Methods

Document Number: NL ISO 14632 : 2018

This standard specifies the requirements and test methods for solid flat extruded sheets of impact-modified polystyrene (PS-I1) without fillers and reinforcing materials. This standard applies only to thickness 0,25 mm to 20,0 mm in accordance with clause 3. This standard also applies to PS-I sheet in roll form.

Extruded sheets of polyethylene (PE-HD) — Requirements and test methods

Document Number: NL ISO 19712 1 : 2018

This standard specifies the requirements and test methods for solid flat extruded sheets of polyethylene homopolymers (PE - HD) without fillers or reinforcing materials. This standard applies only to thicknesses of 0,5 mm to 40 mm. This standard also applies to PE - HD sheet in rolled form.

Plastics — Decorative solid surfacing materials — Part 1: Classification and specifications

Document Number: NL ISO 19712 2 : 2018

ISO 19712-1:2008 establishes a classification system for solid surfacing materials according to their performance. ISO 19712-1:2008 also specifies property requirements for the various types of solid surfacing materials covered by this classification. Requirements are specified for the types that are most generally used, but additional types may be added as required. The specified limit values apply to the most commonly used types of material, but within each classification it may be possible to obtain variants having much higher performance values. These materials are characterized by their homogeneous appearance, renewable surfaces and inconspicuous seams. They are generally classified as solid surface sheets (designed for horizontal, vertical, wet and dry applications) and solid surface shapes (including, but not limited to, kitchen sinks, bathroom sinks, vanity tops, showers, tubs and spas). The important properties of solid surfacing materials are water resistance, thermal shoc

Plastics — Decorative Solid Surfacing Materials — Part 2: Determination of Properties — Sheet Goods

Document Number: NL ISO 19712 3 : 2018

ISO 19712-2:2007 specifies the methods of test for determination of the properties of solid surfacing materials in the form of sheets. These methods are primarily intended for testing the materials specified in ISO 19712‑1.

Plastics — Decorative Solid Surfacing Materials — Part 3: Determination of Properties — Solid Surface Shapes

Document Number: NL EN 438 5 : 2018

ISO 19712-3:2007 specifies the methods of test for determination of the properties of solid surfacing materials in the form of shaped products. These methods are primarily intended for testing the materials specified in ISO 19712‑1.

High-Pressure Decorative Laminates (HPL) - Sheets Based on Thermosetting Resins (usually called laminates) - Part 5: Classification and Specifications for Flooring Grade Laminates Less Than 2 mm Thick Intended for Bonding to Supporting Substrates

Document Number: NL EN 438 6 : 2018

This European Standard applies to six classes of flooring grade laminates less than 2 mm thick produced by using a high pressure process, intended for bonding to supporting substrates, to produce HPL flooring elements. For laminate floor covering applications they meet the surface property requirements specified in EN 13329. High-pressure decorative flooring laminates are characterised by their high resistance to abrasion, aesthetic qualities and durability. They have good hygienic and anti-static properties and are easy to clean and maintain. The requirements in this document apply only to the high-pressure laminate, and additional properties will need to be specified in order to define the functional performance of the finished flooring product. This European Standard applies only to decorative laminates as defined in Clause 3. EN 438-2 specifies the methods of test relevant to this European Standard.

High-Pressure Decorative Laminates (HPL) - Sheets Based on Thermosetting Resins (usually called laminates) - Part 6: Classification and Specifications for Exterior-Grade Compact Laminates of Thickness 2 mm and Greater

Document Number: NL EN 438 7 : 2018

This European Standard applies to Exterior-grade Compact laminates of thickness 2 mm and greater produced by using a high pressure process. It specifies requirements for standard and flame-retardant laminates intended for use under outdoor weather conditions such as direct sunlight rain and frost. Two levels of performance are specified; one for moderate exterior conditions, and the other for severe exterior conditions. Laminates complying with this European Standard are referred to as Exterior-grade Compact laminates, and are characterized by their high tensile strength, high impact resistance, thermal shock resistance, and resistance to weather and corrosion. They are available in a variety of decorative colours, with high resistance to colour change and aging in outdoor applications. When they are self-supporting Exterior-grade Compact laminates are ready for installation, and only require cutting to size, drilling, etc. to suit the application. EN 438-2 specifies the methods of test relevant to this part of EN 438.

High-Pressure Decorative Laminates (HPL) - Sheets Based on Thermosetting Resins (Usually called Laminates) - Part 7: Compact Laminate and HPL Composite Panels for Internal and External Wall and Ceiling Finishes

Document Number: NL EN 438 8 : 2018

This document specifies the health, safety and energy saving requirements for: · Compact laminate panels/sidings for interior wall and ceiling finishes (including suspended ceilings); · HPL composite panels/sidings for interior wall and ceiling finishes (including suspended ceilings); · Compact laminate panels/sidings for exterior wall and ceiling finishes (including suspended ceilings); · HPL composite panels/sidings for exterior wall and ceiling finishes (including suspended ceilings). It also specifies methods for the evaluation of conformity of the product to the requirements, and includes requirements for marking. It covers only the HPL panels for non-structural applications, and does not cover fixing systems. The products are intended for use as wall and ceiling finishes for internal and external applications according to the manufacturer's specifications. The scope of this document does not cover: a) overlaid or veneered wood-based panels where the overlay/veneer is not HPL; b) HPL-surfaced wood-based panels intended for use as structural components. These products are covered by EN 13986 (wood-based panels for use in construction). This document covers only characteristics related to health, safety and energy-saving. All other characteristics are covered in separate European Standards for HPL products (see aAnnex B). b) HPL-surfaced wood-based panels intended for use as structural components. These products are covered by EN 13986 (wood-based panels for use in construction). This European Standard covers only characteristics related to health, safety and energy-saving. All other characteristics are covered in separate European Standards for HPL products (see annex B).

High-Pressure Decorative Laminates (HPL) - Sheets Based on Thermosetting Resins (Usually called Laminates) - Part 8: Classification and Specifications for Design Laminates

Document Number: NL EN 438 9 : 2018

This document specifies performance requirements for design laminates intended for interior use with a design effect surface having a phenolic based core and a decorative surface, not covered by EN 438-3 [1], EN 438-4 [2], EN 438-5 [3] and EN 438-6 [4]. Three surface layer types (metal, wood veneer and pearlescent decor) are defined in this part of EN 438. EN 438-2 specifies the test methods relevant to this part of EN 438.

High-Pressure Decorative Laminates (HPL) - Sheets Based on Thermosetting Resins (Usually called Laminates) - Part 9: Classification and Specifications for Alternative Core Laminates

Document Number: NL ISO 8157 : 2018

This European Standard specifies performance requirements for high-pressure decorative laminates (HPL) intended for interior use, the core compositions of which are not covered by EN 438-3 [1] to EN 438-6 [4] and EN 438-8 [5]. The core composition types (coloured core and metal reinforced core) are defined in this part of EN 438. EN 438-2 specifies the test methods relevant to this part of EN 438.

Fertilizers and soil conditioners -- Vocabulary

Document Number: NL ISO TR 21932 : 2018

ISO 8157:2015 defines terms relating to fertilizers and soil conditioners.

Sustainability in buildings and civil engineering works — A review of terminology

Sector: Environment. Health protection. Safety

Document Number: NL ISO 11223 : 2018

ISO/TR 21932:2013 provides a compilation of terms and definitions of concepts related to both the construction and use of a building or civil engineering works, and the effect of such construction works on sustainability and sustainable development, as applied in the documents of ISO/TC 59/SC 17, Sustainability in buildings and civil engineering works.

Petroleum and Liquid Petroleum Products — Direct Static Measurements — Measurement of Content of Vertical Storage Tanks by Hydrostatic Tank Gauging

Document Number: NL CEN TR 15367 1 : 2018

ISO 11223:2004 gives guidance on the selection, installation, commissioning, maintenance, validation and calibration of hydrostatic tank-gauging (HTG) systems for the direct measurement of static mass in petroleum storage tanks. It is intended to cover custody transfer applications, although details of other, less accurate, measurements are included for information. It also gives guidance on calculations of standard volume from measured mass and independently measured reference density. Information is also included on measurements of observed and standard volume using density measured by the HTG system itself. ISO 11223:2004 is applicable to hydrostatic tank-gauging systems which use pressure sensors with one port open to the atmosphere. It is applicable to the use of hydrostatic tank gauging on vertical, cylindrical, atmospheric storage tanks with either fixed or floating roofs. ISO 11223:2004 is not applicable to the use of hydrostatic tank gauging on pressurized tanks.

Petroleum Products - Guidelines for Good Housekeeping - Part 1: Automotive Diesel Fuels

Document Number: NL CEN TR 15367 2 : 2018

This Technical Report provides general guidance on diesel fuel housekeeping. It does not pre-empt national or local regulations but addresses the issues of contamination by water, sediment, inorganic contaminants, or microbial growth that may occur in the supply chain during manufacture, blending, storage and transportation. It does not address contamination by other fuel products nor does it address possible contamination by water or sediment that may occur on-board vehicles. An informative note on vehicle factors is presented in Annex A, however.

Petroleum Products - Guidelines for Good Housekeeping - Part 2: Automotive Petrol Fuels

Document Number: NL CEN TR 15367 3 : 2018

This document provides general guidance on petrol fuel housekeeping. It does not pre-empt national or local regulations. It addresses the issues of contamination by water or sediment that may occur in the supply chain during manufacture, storage and/or transportation. It does not address contamination by other products, nor does it address possible contamination by water or sediment that may occur on board vehicles, however, an informative note on vehicle factors is presented in Annex A.

Petroleum Products - Guidelines for Good Housekeeping - Part 3: Prevention of Cross Contamination

Document Number: NL EN 12766 1 : 2018

This document provides general guidance on automotive fuel handling. It does not pre-empt national or local regulations. It only addresses the issue of cross contamination between petrol and diesel automotive fuels that may occur in the supply chain, during manufacturing, storage, transportation or distribution. There may also be a risk of contamination with other products such as kerosene/jet fuel and off road diesel. The guidance principles described in this document would apply equally to managing these risks although some details may be different.

Petroleum Products and Used Oils - Determination of PCBs and Related Products - Part 1: Separation and Determination of Selected PCB Congeners by Gas Chromatography (GC) using an Electron Capture Detector (ECD) (EN

Document Number: NL EN 81 41 AMD 1 : 2018

This European Standard specifies a method to determine the concentration of up to 12 individual or defined unresolved small groups of polychlorinated biphenyl (PCB) congeners in petroleum products and related materials by means of a specified gaschromatographic separation procedure. The gas chromatographic separation is valid for the different quantification procedures described in Part 2 of this European Standard. This European Standard is applicable to unused, used and treated (e.g. dechlorinated) petroleum products including synthetic lubricating oils, and to petroleum products and synthetic lubricating oils suitably recovered from other materials, e.g. from waste materials. NOTE 1 The nominal application range does depend on precision, the lower limit per single congener is about 0,2 mg/kg. NOTE 2 For the purposes of this European Standard, the terms “% (V/V)” and “% (m/m)” are used to represent respectively the mass fraction and the volume fraction. This European Standard does not apply to insulating liquids, for which a different method (EN 61619) is available. Depending on current legislation, it may be necessary to measure either total or individual PCB congeners. EN 61619 may be followed as an alternative method for the determination of total PCBs, using the clean-up stage described in clause 8 of this standard. WARNING : The use of this standard can involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Safety Rules For The Construction And Installation Of Lifts – Special Lifts For The Transport Of Persons And Goods - Part 41: Vertical Lifting Platforms Intended For Use By Persons With Impaired Mobility

Document Number: NL EN 81 21 AMD 1 : 2018

1.1 This European Standard deals with safety requirements for construction, manufacturing, installation, maintenance and dismantling of electrically operated stairlifts (chair, standing platform and wheelchair platform) affixed to a building structure, moving in an inclined plane and intended for use by persons with impaired mobility:  travelling over a stair or an accessible inclined surface;  intended for use by one person;  whose carriage is directly retained and guided by a guide rail or rails;  supported or sustained by rope (5.4.4), rack and pinion (5.4.5), chain (5.4.6), screw and nut (5.4.7), friction traction drive (5.4.8), and guided rope and ball (5.4.9). 1.2 The standard identifies hazards as listed in Clause 4 which arise during the various phases in the life of such equipment and describes methods for the elimination or reduction of these hazards when used as intended by the manufacturer. 1.3 This European standard does not specify the additional requirements for:  operation in severe conditions (e.g. extreme climates, strong magnetic fields);  lightning protection;  operation subject to special rules (e.g. potentially explosive atmospheres);  handling of materials the nature of which could lead to dangerous situations;  use of energy systems other than electricity;  hazards occurring during manufacture;  earthquakes, flooding, fire;  type C wheelchairs as defined in EN 12183 and/or EN 12184;  evacuation during a fire;  stairlifts for goods only;  concrete, hardcore, timber or other foundation or building arrangement;  design of anchorage bolts to the supporting structure. NOTE For the actual type of machinery, noise is not considered a significant nor relevant hazard. 1.4 This document is not applicable to power operated stairlifts which are manufactured before the date of publication of this document by CEN.

Safety Rules For The Construction And Installation Of Lifts - Lifts For The Transport Of Persons And Goods - Part 21: New Passenger And Goods Passenger Lifts In Existing Buildings

Document Number: NL EN 81 70 AMD 1 : 2018

This European Standard specifies the safety rules related to new passenger and goods/passenger lifts permanently installed in existing buildings where in some circumstances due to limitations enforced by building constraints, some requirements of EN 81-1 and EN 81-2 cannot be met (see also 4th sentence of Introduction). This European Standard addresses a number of these constraints and gives requirements for alternative solutions. It shall be read and applied in conjunction with the European Standards EN 81-1 or EN 81-2 !deleted text", including their Clause 0. This European Standard covers:  Either the construction and installation of one or more complete new lift(s) including new well and machinery spaces in an existing building; or  The replacement of one or more existing lift(s) by new ones in existing well(s) and machinery spaces. This European Standard does not cover:  Replacement or modifications of some parts to a lift already installed;  Other applications outside of the scope of EN 81-1 or EN 81-2.

Safety rules for the construction and installations of lifts-Particular applications for passenger and good passengers lifts -Part 70: Accessibility to lifts for persons including persons with disability

Document Number: NL EN 81 82 AMD 1 : 2018

This European Standard specifies the minimum requirements for the safe and independent access and use of lifts by persons, including persons with the disabilities mentioned in annex B, Table B.1. This European Standard covers lifts with minimum car dimensions according to Table 1 and provided with car doors and landing doors constructed as automatic power operated horizontally sliding doors. This European Standard considers accessibility to lifts for persons using wheelchairs with maximum overall dimensions defined in EN 12183:1999 and EN 12184:1999. This European Standard also deals with the additional technical requirements to minimise the hazards listed in clause 4 that arise during the operation of lifts intended to be accessible to disabled users. NOTE This standard can be used as guidance for upgrading existing lifts in line with the recommendation of the European Commission dated 8th of June, 1995 (95/216/EC) concerning improvements to safety of existing lifts.

Safety rules for the construction and installation of lifts - Existing lifts - Part 82: Rules for the improvement of the accessibility of existing lifts for persons including persons with disability

Document Number: NL EN 81 40 : 2018

1.1 This European Standard provides rules on how to apply EN 81-70 referred to in EN 81-80:2003, 5.2.1 [4] to existing lifts to improve their accessibility for persons including persons with disability. 1.2 This European Standard applies to permanently installed lifts serving defined landing levels, having a car designed for the transportation of persons or persons and goods and moving between guide rails inclined not more than 15° to the vertical.

Safety Rules For The Construction And Installation Of Lifts –Special Lifts For The Transport Of Persons And Goods - Part 40: Stairlifts And Inclined Lifting Platforms Intended For Persons With Impaired Mobility

Document Number: NL EN 12057 : 2018

Natural stone products - Modular tiles - Requirements

Document Number: NL ISO 13171 : 2018

This European Standard specifies requirements for flat modular tiles of natural stone which are made for internal (including enclosed public transport premises) and/or external uses as floorings, stairs and wall and ceiling finishes. This European Standard does not cover mineral aggregates and artificial agglomerated stone material and does not cover installation.

Essential oil of oregano [Origanum vulgare L. subsp. hirtum (Link) letsw]

Document Number: NL ISO 14021 : 2018

This European Standard specifies the requirements for factory made wood fibre products, with or without facings or coatings, which are used for the thermal insulation of buildings1. The products are manufactured in the form of rolls, batts, felts, boards or slabs. This European Standard specifies product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this European Standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application are to be found in regulations or non-conflicting standards. Products with a declared thermal resistance lower than 0,50 m2⋅K/W or a declared thermal conductivity greater than 0,070 W/(m⋅K) at 10 °C are not covered by this European Standard. This European Standard does not cover in situ insulation products and products intended to be used for the insulation of building equipment and industrial installations.

Environmental labels and declarations -- Self-declared environmental claims (Type II environmental labelling)

Sector: Construction materials and building

Document Number: NL EN 81 22 : 2018

This International Standard specifies requirements for self-declared environmental claims, including statements, symbols and graphics, regarding products. It further describes selected terms commonly used in environmental claims and gives qualifications for their use. This International Standard also describes a general evaluation and verification methodology for self-declared environmental claims and specific evaluation and verification methods for the selected claims in this International Standard. This International Standard does not preclude, override, or in any way change, legal

Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path

Document Number: NL 137 : 2018

1.1 This European Standard specifies the safety rules for the construction and installation of permanently installed new electric lifts, with traction or positive drive, serving defined landings levels, having a vehicle designed to convey passengers or passengers and loads, suspended by ropes or chains and travelling in a vertical plan along guide rails that are inclined at an angle of between 15° and 75° in relation to the horizontal. 1.2 In addition to the requirements of this standard, supplementary requirements should be considered in special cases (potentially explosive atmosphere, extreme climate conditions, seismic conditions, transporting dangerous goods, etc.). 1.3 This European Standard does not cover: a) lifts with drives other than those stated in 1.1; b) installation of electric lifts in existing buildings to the extent that space does not permit; c) important modifications (see Annex E) to a lift installed before this standard is brought into application; d) lifting appliances, such as paternosters, mine lifts, theatrical lifts, appliances with automatic caging, skips, lifts and hoists for building and public works sites, ships' hoists, platforms for exploration or drilling at sea, construction and maintenance appliances; e) safety during transport, installation, repairs, and dismantling of lifts; f) lifts with rated speed ≤ 0,15 m/s. However, this standard may usefully be taken as a basis. Noise is not dealt with in this standard because it is not relevant to the safe use of the lift. Vibrations are dealt with for electric parts only. Direct effects on human bodies are not considered as harmful. 1.4 This European Standard does not specify the additional requirements necessary for the use of lifts in case of fire. 1.5 Taking into account the state of art, the scope of the present standard is limited as follows: — inclination: a variation in inclination is permitted for the travel path; — travel path: confined within the vertical plane; — maximum capacity of the car: 7 500 kg (100 passengers); — maximum rated speed (v): 4 m/s. Both characteristics (capacity and speed) are linked by the relation given in the following Figure 1.

Wind Action on Buildings

Document Number: NL 604 : 2018

(1) The present Standard gives rules and methods of calculation for loads of wind exercised on buildings of height lower than 200 ms, their components and their appendixes. (2) Loads of wind must be calculated for each of zones affected by these actions: - the whole of the structure; - or a part of the structure, that is some of his/her/its elements, shifting boards and their fixings. (3) The present Standard also gives rules for chimneys and other recessed structures in foot. The relative special conditions to towers in lattice don't appear there.

Foods for special dietary use for persons intolerant to gluten

Sector: Food Technology

Document Number: NL ISO 10245 4 : 2018

تطبق هذه المواصفة القياسية على الأغذية المصنعة والمحضرة خصيصاً كي تلائم احتياجات الحمية للأشخاص الذين يعانون عدم تحمل الغلوتين. كما تشير هذه المواصفة حصراً الى التدابير الخاصة المتعلقة بالغرض التغذوي المحدد الذي ترمي اليه هذه الأغذية. ولا تطبق هذه المواصفة على الأغذية الخلوة أصلاً وبشكلها الطبيعي من الغلوتين.

Cranes — Limiting and indicating devices — Part 4: Jib cranes

Document Number: NL ISO 10245 5 : 2018

This part of ISO 10245 specifies the requirements for devices which limit and/or indicate the loads, motions, performance and environment of jib-type cranes as defined in ISO 4306-1, other than offshore, tower, mobile and railway cranes, which are covered in the other parts of ISO 10245. The general requirements for limiting and indicating devices for cranes are given in ISO 10245-1:1994.

Cranes -- Limiting and indicating devices -- Part 5: Overhead travelling and portal bridge cranes

Document Number: NL ISO 374 1 : 2018

This part of IS0 10245 specifies the requirements for devices which limit and/or indicate the loads, motions, performance and environment of bridge and gantry cranes. The general requirements for limiting and indicating devices for cranes are given in IS0 10245-I.

Protective gloves against dangerous chemicals and microorganisms — Part 1: Terminology and performance requirements for chemical risks

Document Number: NL ISO 374 5 : 2018

This part of ISO 374 specifies the requirements for protective gloves intended to protect the user against dangerous chemicals and defines terms to be used. NOTE If other protection features have to be covered, e.g. mechanical risks, thermal risks, electrostatic dissipation etc., the appropriate specific performance standard is to be used in addition. Further information on protective gloves standards can be found in the EN 420.

Protective gloves against dangerous chemicals and microorganisms — Part 5:Terminology and performance requirements for micro-organisms risks

Document Number: NL ISO TR 2801 : 2018

This part of ISO 374 specifies the requirements and test methods for protective gloves intended to protect the user against micro-organisms. NOTE If other protection features is to be needed, e.g. chemical risks

Clothing for protection against heat and flame — General recommendations for selection, care and use of protective clothing

Document Number: NL ISO 3873 : 2018

This Technical Report sets out guidance for the selection, use, care and maintenance of clothing designed to provide protection against heat and flame.

Industrial safety helmets

Document Number: NL ISO 4007 : 2018

This lnternational Standard specifies physical and Performance requirements, methods of test and marking requirements for industrial safety helmets.

Personal protective equipment — Eye and face protection — Vocabulary

Document Number: NL ISO 4849 : 2018

This International Standard defines and explains the principal terms used in the field of personal eye and face protection. NOTE This International Standard includes terms reproduced from the standards cited in Clause 2. At the time of publication of this International Standard, the quoted terms are identical to those in ISO 8624:2011, ISO 13666:1, CIE 17.4:1987 and ISO/IEC Guide 51:1999. If, due to future revision of the aforementioned standards, there should be a disagreement between ISO 4007 and ISO 8624, ISO 13666, CIE 17.4 or ISO/IEC Guide 51, then the definitions in the latest version of ISO 8624, ISO 13666, CIE 17.4 or ISO/IEC Guide 51 take precedence.

Personal eye-protectors -- Specifications

Document Number: NL ISO 4850 : 2018

This International Standard specifies functional requirements for the various types of personal eye-protectors used mainly in industry.

Personal eye-protectors for welding and related techniques -- Filters -- Utilisation and transmittance requirements

Document Number: NL ISO 4851 : 2018

ISO/IEC 27033-6:2016 describes the threats, security requirements, security control and design techniques associated with wireless networks. It provides guidelines for the selection, implementation and monitoring of the technical controls necessary to provide secure communications using wireless networks. The information in this part of ISO/IEC 27033 is intended to be used when reviewing or selecting technical security architecture/design options that involve the use of wireless network in accordance with ISO/IEC 27033‑2. Overall, ISO/IEC 27033‑6 will aid considerably the comprehensive definition and implementation of security for any organization's wireless network environment. It is aimed at users and implementers who are responsible for the implementation and maintenance of the technical controls necessary to provide secure wireless networks.

Personal eye-protectors -- Ultra-violet filters -- Utilisation and transmittance requirements

Document Number: NL ISO 4852 : 2018

This International Standard specifies the numbering of, and transmittance requirements for filters for protection against ultra-violet radiation. It also gives guidance on their selection and use. Eye-protectors used for protection against ultra-violet radiation shall meet the general requirements given in ISO 4849. The latter also deals with general considerations relating to eye-protectors, such as identification. Optical test methods for eye-protectors form the subject of SS0 4854. Non-Optical test methods for eye-protectors form the subject of ISO 4855.

Personal eye-protectors -- Infra-red filters -- Utilisation and transmittance requirements

Document Number: NL ISO 4854 : 2018

This International Standard specifies the numbering of, and the transmittance requirements for, filters for protec- tion against infra-red radiation. lt also gives guidance on their selection and use. Eye-protectors used for protection against infra-red radiation shall meet the general requirements given in ISO 4849. The latter also deals with general considerations relating to eye-protectors, such as identification. Optical test methods for eye-protectors form the subject of ISO 4854. Non-Optical test methods for eye-protectors form the subject of ISO 4855.

Personal eye-protectors -- Optical test methods

Document Number: NL ISO 4855 : 2018

This International Standard specifies the Optical test methods for eye-protectors the requirements for which are given in ISO 4849 to ISO 4853.‘ ) The test methods other than Optical test methods are given in ISO 4855.

Personal eye-protectors -- Non-optical test methods

Document Number: NL ISO 23853 : 2018

This International Standard specifies the non-Optical test methods for eye-protectors the requirements for which are given in ISO 4849 to 4853. The Optical test methods are given in ISO 4854. PRELIMINARY REMARK - Of the tests described, the test for stability at elevated temperature should be carried out first on eye-protectors, generally followed by the test for robustness.

Cranes — Training of slingers and signaller

Document Number: NL ISO 13200 : 2018

This International Standard specifies the minimum training to be given to trainee crane slingers and crane signallers to develop the basic slinging skills and to impart the requisite knowledge for competency required for slingers and signallers as defined in ISO 15513.

Cranes -- Safety signs and hazard pictorials -- General principles

Document Number: NL ISO 4190 1 : 2018

This International Standard establishes general principles for the design and application of safety signs and hazard pictorials permanently affixed to cranes as defined in ISO 4306-1. This International Standard outlines safety sign objectives, describes the basic safety sign formats, specifies colours for safety signs, and provides guidance on developing the various Panels that together constitute a safety sign.

NULL

Sector: NULL

Document Number: NL ISO 4190 2 : 2018

ISO 4190-1:2010 specifies the necessary dimensions to permit the installation of passenger lifts of class I, II, III and VI. The dimensions given reflect the requirements for the apparatus. ISO 4190-1:2010 is applicable to all new lift installations, irrespective of drive systems, including a car with entrance, to be installed in a new building.

Lift (US: Elevator) installation —Part 2:Class IV lifts

Sector: