Libnor | Catalogs |

Document Number: NL ISO 4190 5 : 2018

Establishes the dimensions relating to the installation of lifts comprising a car the interior of which is inaccessible to persons due to its dimensions and means of construction, running at least partially between rigid guides which are vertical or whose inclination to the vertical is less than 15 . Part 1 covers the lifts of classes I, II and III, part 2 the lifts of class IV, part 5 control devices, signals and additional fittings, and part 6 planning and selection of passenger lifts.

Lift (Elevator) installation —Part 5:Control devices, signals and

Sector:

Document Number: NL EN 14434 : 2018

ISO 4190-5:2006 specifies the control devices, buttons and indicators to be provided when a lift (US: elevator) is constructed and installed, taking into account the type of control intended for the lift and also ensuring the ease of access for disabled persons (motor and/or sensory). It also specifies the requirements for handrails when provided in the car. It is applicable to lifts of classes I to IV and VI as defined in ISO 4190-1 and ISO 4190-2.

Writing boards for educational institutions - Ergonomic, technical and safety requirements and their test methods

Sector: SERVICES. COMPANY ORGANIZATION, MANAGEMENT AND QU

Document Number: NL EN 12727 : 2018

This European Standard specifies ergonomic, technical and safety requirements for wall mounted and freestanding writing boards for use in rooms for educational and training purposes, e.g. classrooms, lecture theatres for schools, universities, etc. It is intended to prevent serious injury through normal functional use, as well as misuse that might reasonably be expected to occur. This document applies to units after installation. Safety depending on the structure of the building is not included, e.g. the strength of wall mounted boards includes only the board and its parts. The wall and the wall attachment are not included. Requirements concerning electrical safety are not included. Annex A (normative) includes an assessment scale for the ability to write and erase. Annex B (informative) includes terminology for display writing boards. Annex C (informative) includes significant technical differences between this document and EN 14434:2004.

Furniture - Ranked seating - Requirements for safety, strength and durability

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT.

Document Number: NL CEN TS 16209 : 2018

This European Standard specifies requirements determining the safety, structural strength and durability of all types of seating that are permanently fastened to the floor and/or wall, whether in bench or individual seat form. This standard does not apply to linked seating not fastened to the floor and/or walls and street furniture. It does not include requirements for resistance to ageing, degradation, flammability, the effect of ambient temperature and the durability of upholstery materials. The standard has two annexes: — Annex A (normative) Additional test methods; — Annex B (informative) Test severity in .relation to application

Furniture - Classification for properties for furniture surfaces

Sector:

Document Number: NL ISO 20712 3 : 2018

This Technical Specification specifies a system for the classification of the resistance to: - Dry heat - Wet heat - Cold liquids - Abrasion - Scratching For resistance to dry heat, resistance to wet heat, and resistance to cold liquids, this Technical Specification applies to all furniture surfaces regardless of materials, except finishes on leather and fabrics. The classification for the surface resistance to abrasion applies to foil, laminate, melamine faced boards, pigmented and transparent coatings. It does not apply to the surfaces covered by EN 14434. The classification for the surface resistance to scratching has two methods, A and B. Method A applies to all types of surface coatings and coverings except for melamine faced boards and HPL. Method B applies to all types of surfaces. It does not apply to finishes on leather and fabrics.

Water safety signs and beach safety flags — Part 3: Guidance for use

Sector: GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUM

Document Number: NL ISO 12821 : 2018

This part of ISO 20712 gives guidance for the selection and use of water safety signs as specified in ISO 20712‑1 and beach safety flags as specified in ISO 20712‑2, in aquatic environments. It provides guidance on their location, mounting positions, lighting and maintenance. It also provides guidance on the design and location of multiple signs. This part of ISO 20712 does not apply to traffic signs for use on the public highway or maritime signalling. It is not applicable to flags for use on firing ranges or to flags used to indicate water quality. It does not cover means of escape signs and their illumination which may be present. NOTE The illustrations in this part of ISO 20712 are as accurate as possible within the limitations of the printing process.

Glass Packaging — 26 H 180 Crown Finish — Dimensions

Sector: Packaging and Distribution of Goods

Document Number: NL ISO 12822 : 2018

This International Standard specifies the dimensions of the 26-mm-tall crown finish for glass bottles containing beverages. The tall crown finish is designed to use a metal crown closure (see CE. T.I.E. data sheet EC 01-02 Revision 1).

Glass Packaging — 26H 126 Crown Finish — Dimensions

Sector: Packaging and Distribution of Goods

Document Number: NL EN 957 7 : 2018

This International standard specifies the dimensions of the 26 mm shallow crown finish for glass bottles containing beverages. The shallow crown finish is designed to use a metal crown closure (see CE.T.I.E. data sheet EC1-02 revision 1).

Stationary training equipment - Part 7: Rowing machines, additional specific safety requirements and test methods

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT

Document Number: NL EN 957 7 : 2018

This Standard Specifies safety requirements for rowing machines in addition to the general safety requirements of EN 957-1 and should be read in conjunction with it. This part of EN 957 is applicable to stationary training equipment type rowing machines, hereinafter referrd to as rowing machines, within the classes S and H and class A regarding accuracy. If accessories are provided with the rowing machine for the performance of additional exercises these are subject to the requirements of EN 957-1 and any other specific requirements of the appropriate prt of this standard.

Stationary training equipment - Part 7: Rowing machines, additional specific safety requirements and test methods

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT

Document Number: NL ISO 16276 1 : 2018

Specifies safety requirements for rowing machines in addition to the general safety requirements of EN 957-1 and should be read in conjunction with it. This part of EN 957 is applicable to stationary training equipment type rowing machines, hereinafter referrd to as rowing machines, within the classes S and H and class A regarding accuracy. If accessories are provided with the rowing machine for the performance of additional exercises these are subject to the requirements of EN 957-1 and any other specific requirements of the appropriate prt of this standard.

Corrosion Protection of Steel Structures by Protective Paint Systems — Assessment of, and Acceptance Criteria for, the Adhesion/ Cohesion (Fracture Strength) of a Coating — Part 1: Pull-off Testing

Sector: PAINT AND COLOUR INDUSTRIES

Document Number: NL ISO 16276 2 : 2018

This part of ISO 16276 specifies procedures for assessing the fracture strength of a protective paint coating of any thickness on a steel substrate of thickness not less than 10 mm. The procedures given in this part of ISO 16276 are based on methods used with different types of pull-off test equipment. The results obtained using such different types of equipment are not comparable. NOTE 1 Substrates of less than 10 mm in thickness can be tested if they are strengthened by the sandwich technique (see ISO 4624) or by the nature of the structure (e.g. I-beam or backing-plate). Otherwise, test panels with a thickness of at least 10 mm coated in the same way as the structure can be used, or the method specified ISO 16276-2 can be used. This part of ISO 16276 is only applicable if a fracture strength value is specified, together with the type of test equipment and the manufacturer of the equipment. Usually, this information is included in contract documentation. NOTE 2 A value for the fracture strength is only meaningful if the requirements concerning the ambient conditions (see 6.4.2) are met. This part of ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans andacceptance/rejection criteria. It does not give any values of the fracture strength of different protective paint coatings.

Corrosion Protection of Steel Structures by Protective Paint Systems — Assessment of, and Acceptance Criteria for, the Adhesion/ Cohesion (Fracture Strength) of a Coating — Part 2: Cross-cut Testing and X-Cut Testing

Sector: PAINT AND COLOUR INDUSTRIES

Document Number: NL ISO 29601 : 2018

This part of ISO 16276 specifies procedures for rating the resistance of coating systems when a cut in the form of a right-angle lattice pattern (cross-cut) or in the form of an X (X-cut) is made into the coating, penetrating through to the substrate. This part of ISO 16276 is only applicable if the cross-cut or X-cut test method is specified, together with the rating from the appropriate rating scale. NOTE The characteristics of the coating can make the assessment of the result of a cross-cut or X-cut test difficult. This part of ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria. It does not specify ratings for particular coating systems.

Paints and Varnishes — Corrosion Protection by Protective Paint Systems — Assessment of Porosity in a Dry Film

Sector: PAINT AND COLOUR INDUSTRIES

Document Number: NL ISO 7823 1 : 2018

This International Standard specifies procedures for detecting the presence of porosity in a protective paint system of any thickness on a steel or other metallic substrate. The procedures given in this International Standard are based on methods using two different types of test equipment, the choice of equipment depending on the dry film thickness. These procedures are only applicable to the testing of electrically nonconductive parts of a paint system. The test methods specified are mainly intended for use with new coatings, but can also be used for coatings which have been in service for some time. In the latter case, it is important to bear in mind that the coating might have been penetrated by substances in contact with the coating during service.

Plastics — Poly(methyl methacrylate) Sheets ― Types, Dimensions and Characteristics — Part 1: Cast Sheets

Sector: Rubber and Plastics Industries

Document Number: NL ISO 7823 2 : 2018

This part of ISO 7823 specifies requirements for non-modified flat poly(methyl methacrylate) (PMMA) cast sheets (plates) for general-purpose use. The sheets may be colourless or coloured, and may be transparent, translucent or opaque. The thickness range of the sheets covered by this part of ISO 7823 is 1,5 mm to 25 mm.

Plastics — Poly(methyl methacrylate) Sheets ― Types, Dimensions and Characteristics — Part 2: Extruded Sheets

Sector: Rubber and Plastics Industries

Document Number: NL ISO 7823 3 : 2018

This part of ISO 7823 specifies requirements for flat poly(methyl methacrylate) (PMMA) sheets extruded from colourless or coloured, transparent, translucent or opaque materials as defined in 3.1. The thickness range of the sheets covered by this part of ISO 7823 is 1,5 mm to 20 mm.

Plastics — Poly(methyl methacrylate) Sheets ― Types, Dimensions and Characteristics — Part 3: Continuous Cast Sheets

Sector: Rubber and Plastics Industries

Document Number: NL 804 : 2018

This part of ISO 7823 specifies requirements for non-modified flat poly(methyl methacrylate) (PMMA) continuous cast sheets for general-purpose use. The sheets may be colourless or coloured, and may be transparent, translucent or opaque. The thickness range of the sheets covered by this part of ISO 7823 is 1 mm to 10 mm.

Physical and Chemical Properties of Engine Oils

Sector: Chemical Technology

Document Number: NL ISO 20474 4 : 2018

The procedure for the preparation of a principal solution for chemical analysis requires at first an alkaline fusion of the test portion, either with a mixture of sodium carbonate and boric acid or with a mixture of sodium carbonate and sodium tetraborate. Subsequent dissolution of the molten mass in an excess of nitric acid and adjustment of an appropriate aliquot portion to pH 2. Replaces ISO Recommendation R804/1968.

Earth-moving machinery — Safety — Part 7: Requirements for scrapers

Document Number: NL ISO 20474 5 : 2018

ISO 20474-4:2017 gives the safety requirements specific to wheeled and crawler backhoe loaders as defined in ISO 6165. It is intended to be used in conjunction with ISO 20474‑1, which specifies general safety requirements common to two or more earth-moving machine families. The specific requirements given in this document take precedence over the general requirements of ISO 20474‑1. ISO 20474-4:2017 deals with all significant hazards, hazardous situations and events relevant to the earth-moving machinery within its scope (see ISO 20474‑1:2017, Annex A) when used as intended or under conditions of misuse reasonably foreseeable by the manufacturer. It specifies the appropriate technical measures for eliminating or reducing risks arising from relevant hazards, hazardous situations or events during commissioning, operation and maintenance. ISO 20474-4:2017 is not applicable to machines manufactured before the date of its publication.

Earth-moving machinery — Safety — Part 5: Requirements for hydraulic excavators

Document Number: NL ISO 20474 6 : 2018

ISO 20474-5:2017 gives the safety requirements specific to hydraulic excavators as defined in ISO 6165. It is intended to be used in conjunction with ISO 20474-1, which specifies general safety requirements common to two or more earth-moving machine families. The specific requirements given in this document take precedence over the general requirements of ISO 20474-1. ISO 20474-5:2017 deals with all significant hazards, hazardous situations and events relevant to the earth-moving machinery within its scope (see ISO 20474-1:2017, Annex A) when used as intended or under conditions of misuse reasonably foreseeable by the manufacturer. It specifies the appropriate technical measures for eliminating or reducing risks arising from relevant hazards, hazardous situations or events during commissioning, operation and maintenance. ISO 20474-5:2017 is not applicable to machines manufactured before the date of its publication.

Earth-moving machinery — Safety —Part 6: Requirements for dumpers

Document Number: NL ISO 20474 7 : 2018

ISO 20474-6:2017 gives the safety requirements specific to wheeled and crawler dumpers as defined in ISO 6165, including compact dumpers with seated or standing operator. It is not applicable to dumpers primarily designed for use on public roads. It is intended to be used in conjunction with ISO 20474‑1, which specifies general safety requirements common to two or more earth-moving machine families. The specific requirements given in this document take precedence over the general requirements of ISO 20474‑1. ISO 20474-6:2017 deals with all significant hazards, hazardous situations and events relevant to the earth-moving machinery within its scope (see ISO 20474‑1:2017, Annex A) when used as intended or under conditions of misuse reasonably foreseeable by the manufacturer. It specifies the appropriate technical measures for eliminating or reducing risks arising from relevant hazards, hazardous situations or events during commissioning, operation and maintenance. ISO 20474-6:2017 is not applicable to machines manufactured before the date of its publication.

Earth-moving machinery — Safety — Part 7: Requirements for scrapers

Document Number: NL ISO 20474 8 : 2018

ISO 20474-7:2017 gives the safety requirements specific to wheeled scrapers and crawler scrapers, excepting towed scrapers, as defined in ISO 6165. It is intended to be used in conjunction with ISO 20474-1, which specifies general safety requirements common to two or more earth-moving machine families. The specific requirements given in this document take precedence over the general requirements of ISO 20474‑1. ISO 20474-7:2017 gives the safety requirements specific to wheeled scrapers and crawler scrapers, deals with all significant hazards, hazardous situations and events relevant to the earth-moving machinery within its scope (see ISO 20474-1:2017, Annex A) when used as intended or under conditions of misuse reasonably foreseeable by the manufacturer. It specifies the appropriate technical measures for eliminating or reducing risks arising from relevant hazards, hazardous situations or events during commissioning, operation and maintenance. ISO 20474-7:2017 gives the safety requirements specific to wheeled scrapers and crawler scrapers, is not applicable to machines manufactured before the date of its publication.

Earth-moving machinery — Safety —Part 8:Requirements for graders

Document Number: NL EN 13950 : 2018

ISO 20474-8:2017 gives the safety requirements specific to graders as defined in ISO 6165. It is intended to be used in conjunction with ISO 20474‑1, which specifies general safety requirements common to two or more earth-moving machine families. The specific requirements given in this document take precedence over the general requirements of ISO 20474‑1. ISO 20474-8:2017 deals with all significant hazards, hazardous situations and events relevant to the earth-moving machinery within its scope (see ISO 20474‑1:2017, Annex A) when used as intended or under conditions of misuse reasonably foreseeable by the manufacturer. It specifies the appropriate technical measures for eliminating or reducing risks arising from relevant hazards, hazardous situations or events during commissioning, operation and maintenance. ISO 20474-8:2017 is not applicable to machines manufactured before the date of its publication.

Gypsum board thermal/acoustic insulation composite panels - Definitions, requirements and test methods

Document Number: NL EN 14496 : 2018

This European Standard specifies the characteristics and performance of thermal/acoustic insulation composite panels made of an insulating material laminated to gypsum boards for which the main intended use is the internal insulation (thermal and/or acoustic) of walls. They are attached with adhesives or by mechanical fixings to vertical solid backgrounds and by mechanical fixings to wood or metal framing with the gypsum board face exposed. The method of fixing and jointing should ensure that the insulating material is not exposed in its normal application. This European Standard covers the following performance characteristics: reaction to fire, fire resistance, water vapour permeability, flexural strength, impact resistance, direct airborne sound insulation and thermal resistance to be measured according to the corresponding European test methods. It provides for the assessment and verification of constancy of performance of the products to this European Standard. This European Standard covers also additional technical characteristics that are of importance for the use and acceptance of the product by the construction industry.

Gypsum based adhesives for thermal/acoustic insulation composite panels and gypsum boards - Definitions, requirements and test methods

Document Number: NL ISO 12480 1 : 2018

This European Standard specifies the characteristics and performances of gypsum based adhesives which are composed of gypsum plasters defined in EN 13279-1 and of additives. These adhesives are used for fixing to walls and partitions, gypsum board thermal/acoustic insulation composite panels according to EN 13950, gypsum plasterboard linings according to EN 520, gypsum boards with mat reinforcement according to EN 15283-1, gypsum fibre boards according to EN 15283-2 and other suitable products as reprocessed boards according to EN 14190 and cornices according to EN 14209. They assist in the construction of systems which provide thermal and acoustic performance. It covers the following performance characteristics: reaction to fire, fire resistance and bond strength to be measured according to the corresponding European test methods. It provides the assessment and verification of constancy of performance of the products. This standard covers also additional technical characteristics that are of importance for the use and acceptance of the product by the construction Industry and the reference tests for these characteristics.

Cranes - Safe use - Part 1: General

Sector: MATERIALS HANDLING EQUIPMENT

Document Number: NL ISO 15513 : 2018

This part of IS0 12480 establishes required practices for the safe use of cranes, including safe systems of work, management, planning, selection, erection and dismantling, operation and maintenance of cranes and the selection of drivers, slingers and signallers. It does not cover manually operated (non-powered) cranes, cranes in which at least one of its motions is manually operated and cranes mounted on water-borne vessels, except in those circumstances where a land-based crane is temporarily affixed to a vessel.

Cranes -- Competency requirements for crane drivers (operators), slingers, signallers and assessors

Document Number: NL ISO 23813 : 2018

This International Standard gives competency requirements applicable for the selection, training, assessment and verification of crane drivers (operators), slingers, signallers and their assessors. This International Standard does not cover additional competency requirements needed for special operations, e.g. man-lifting, pile-driving or pile-pulling. NOTE 1 Responsibilities for the performance of tasks are given in ISO 12480-1. However, personnel need to be aware of the responsibilities of others; inclusion in the training programme should not infer any changes in responsibilities. NOTE 2 For training of drivers (operators), see ISO 9926.

Cranes — Training of appointed persons

Document Number: NL ISO IEC 27033 2 : 2018

This International Standard specifies the minimum training needed to impart the requisite knowledge for a person appointed to control and manage the lifting operations of cranes. It is not applicable to the additional training required for those persons controlling and managing lifting operations involving dangerous goods or hazardous areas. NOTE 1 Responsibilities for the performance of tasks are given in ISO 12480-1. NOTE 2 For the training of drivers and operators, slingers and signallers, see ISO 9926-1 and ISO 23853, respectively.

NULL

Document Number: NL ISO IEC 27033 3 : 2018

ISO/IEC 27033-2:2012 gives guidelines for organizations to plan, design, implement and document network security.

NULL

Document Number: NL ISO IEC 27033 4 : 2018

ISO/IEC 27033-3:2010 describes the threats, design techniques and control issues associated with reference network scenarios. For each scenario, it provides detailed guidance on the security threats and the security design techniques and controls required to mitigate the associated risks. Where relevant, it includes references to ISO/IEC 27033-4 to ISO/IEC 27033-6 to avoid duplicating the content of those documents. The information in ISO/IEC 27033-3:2010 is for use when reviewing technical security architecture/design options and when selecting and documenting the preferred technical security architecture/design and related security controls, in accordance with ISO/IEC 27033-2. The particular information selected (together with information selected from ISO/IEC 27033-4 to ISO/IEC 27033-6) will depend on the characteristics of the network environment under review, i.e. the particular network scenario(s) and ‘technology' topic(s) concerned. Overall, ISO/IEC 27033-3:2010 will aid consi

NULL

Document Number: NL ISO IEC 27033 5 : 2018

ISO/IEC 27033-4:2014 gives guidance for securing communications between networks using security gateways (firewall, application firewall, Intrusion Protection System, etc.) in accordance with a documented information security policy of the security gateways, including: identifying and analysing network security threats associated with security gateways; defining network security requirements for security gateways based on threat analysis; using techniques for design and implementation to address the threats and control aspects associated with typical network scenarios; and addressing issues associated with implementing, operating, monitoring and reviewing network security gateway controls.

NULL

Document Number: NL ISO IEC 27033 6 : 2018

ISO/IEC 27033-5:2013 gives guidelines for the selection, implementation, and monitoring of the technical controls necessary to provide network security using Virtual Private Network (VPN) connections to interconnect networks and connect remote users to networks.

NULL

Document Number: NL EN 12520 : 2018

ISO/IEC 27033-6:2016 describes the threats, security requirements, security control and design techniques associated with wireless networks. It provides guidelines for the selection, implementation and monitoring of the technical controls necessary to provide secure communications using wireless networks. The information in this part of ISO/IEC 27033 is intended to be used when reviewing or selecting technical security architecture/design options that involve the use of wireless network in accordance with ISO/IEC 27033‑2. Overall, ISO/IEC 27033‑6 will aid considerably the comprehensive definition and implementation of security for any organization's wireless network environment. It is aimed at users and implementers who are responsible for the implementation and maintenance of the technical controls necessary to provide secure wireless networks.

Furniture - Strength, durability and safety - Requirements for domestic seating

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT.

Document Number: NL EN 16121 : 2018

This European Standard specifies the minimum requirements for the safety, strength and durability of all types of domestic seating for adults. It does not apply to ranked seating, seating for non-domestic use, office work chairs, office visitors chairs, chairs for educational institutions, outdoor seating and to links for linked seating for which European Standards exist. It does not include requirements for the durability of upholstery materials, castors, reclining and tilting mechanisms and seat height adjustment mechanisms. It does not include requirements for electrical safety. It does not include requirements for the resistance to ageing, degradation, flammability and ergonomics. The tests are based on use by persons weighing up to 110 kg.

Non-domestic storage furniture - Requirements for safety, strength, durability and stability

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL ISO 2556 : 2018

This European Standard specifies requirements for the safety, strength, durability and stability for all types of non-domestic storage furniture. It does not apply to domestic storage, office storage, industrial storage, kitchen, catering equipment, retail storage !deleted text" and industrial storage lockers. Requirements for strength and durability do not apply to the structure of the building for example the strength of wall hanging cabinets includes only the cabinets and the parts used for attachment. The wall and the wall attachments are not included. It does not include requirements for the resistance to ageing, degradation and flammability.

NULL

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT.

Document Number: NL ISO 11963 : 2018

Specification of the methodand of two types of suitable test apparatus. The plastic test specimen separates two chambers, the one contains the test gas at atmospheric pressure, the other of known initial volume has the air pumped out until the pressure is practically zero. The quantity of gas which passes through the specimen from one chamber to the other is determined as a function of time by measuring the increase in pressure occuring in the second chamber by means of a manometer.

NULL

Document Number: NL EN 14190 : 2018

This document specifies the requirements for solid, flat extruded sheets of polycarbonate (PC) for general applications. It applies specifically to sheets made of poly(p,p′-isopropylidene-diphenyl carbonate). The sheets can be coloured or colourless, and they can be transparent, translucent or opaque. The sheets can also be those that have a special weather-protective layer on one or both surfaces. This document applies only to thicknesses equal to or greater than 1,5 mm.

Gypsum board products from reprocessing - Definitions, requirements and test methods

Sector: CONSTRUCTION MATERIALS AND BUILDING

Document Number: NL EN 14195 : 2018

This European Standard specifies the characteristics and performance of products which have been produced by reprocessing gypsum boards manufactured according to EN 520, EN 15283 1 and EN 15283 2. Reprocessing may include cutting, perforating, edge profiling, decorating and laminating membranes of other materials for functional or decorative purposes, attaching fixings including supports e.g. for partitions. Examples of reprocessing operations are given in Annex B. The products are intended for use in wall, ceiling and floor applications, where they may be fixed directly to the background, or they are used in systems assembled in conjunction with the structure to form separate or suspended linings. The products can be customized to fit the intended application offering a wide range of aesthetic, functional and decorative solutions of modular or non-modular design. This European Standard does not cover gypsum board thermal/acoustic insulation composite panels according to EN 13950 and p

Metal framing components for gypsum board systems -Definitions, requirements and test methods

Document Number: NL EN 13963 : 2018

This European Standard specifies the characteristics of metal framing components (e.g. profiles, hangers and connectors) intended to be used in building construction works in conjunction with gypsum boards manufactured according to EN 520, EN 15283 1 and EN 15283 2 and gypsum board products from reprocessing conforming to EN 14190 where the assembly is non-loadbearing. Such assemblies include, for example, partitions, wall and ceiling linings, ceilings with mechanically fixed boards and the cladding of beams, columns, ducts and shafts. It covers the following performance characteristics: reaction to fire, flexural (yield) strength and loadbearing capacity of suspension components to be measured according to the relevant test methods as specified or cited in this European Standard.

Jointing materials for gypsum boards - Definitions, requirements and test methods

Document Number: NL EN 1129 1 : 2018

Specifies the characteristics of 90 mm Optical Disk Cartridges (ODC) with a capacity of 230 Mbytes per cartridge. Specifies three related, but different implementations of such cartridges: Type R/W, type P-ROM and type O-ROM. Provides for interchange between optical disk drives. Together with a standard for volume and file structure, it provides for full data interchange between data processing systems.

Furniture – Foldaway beds- Safety requirements and testing – Part 1: Safety requirements

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT.

Document Number: NL EN 1129 2 : 2018

This standard specifies requirements relating to the safety and strength of foldaway beds for domestic use. The standard also covers the strength of wall fastenings where applicable and doesn't specify the properties or materials or electrical equipment used in the construction of foldaway beds. folding beds, camping beds, and convertible beds /chairs or settees are not covered by this standard .for

Furniture – Foldaway beds- Safety requirements and testing – Part 2: Test methods

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT.

Document Number: NL EN 1728 : 2018

This part specifies the test methods that asses the safety of .foldaway beds for domestic , camping beds, and convertible beds /chairs or settees are not covered by this standard

Furniture - Seating - Test methods for the determination of strength and durabilit

Sector: DOMESTIC AND COMMERCIAL EQUIPMENT. ENTERTAINMENT.

Document Number: NL EN 267 : 2018

This European Standard specifies test methods for the determination of strength and durability of the structure of all types of seating without regard to use, materials, design/construction or manufacturing process. This European Standard does not apply to children’s highchairs, table mounted chairs and bath seats which are covered by other European Standards. Test methods for the assessment of ageing, degradation, ergonomics and electrical functions are not included. The test methods are not intended to assess the durability of upholstery materials, such as upholstery filling materials and upholstery covers. This European Standard does not include any requirements. Requirements for different end uses can be found in other Standards.

Automatic forced draught burners for liquid fuels

Sector: ENERGY AND HEAT TRANSFER ENGINEERING

Document Number: NL EN 676 : 2018

This European Standard specifies the terminology, the general requirements for the construction and operation of automatic forced draught oil burners and also the provision of control and safety devices, and the test procedure for these burners. This European Standard applies to automatic forced draught oil burners supplied with:  a fuel having a viscosity at the burner inlet of 1,6 mm²/s (cSt) up to 6 mm²/s (cSt) at 20 °C; and  higher boiling petroleum based first raffinates (viscosity greater than 6 mm2/s), that require preheating for proper atomisation. This European Standard is applicable to:  single burners fitted to a single combustion chamber;  single burners fitted to an appliance with additional requirements, then the relevant standard of this appliance shall be taken into account;  single-fuel and dual-fuel burners when operating on oil only;  the oil function of dual-fuel burners designed to operate simultaneously on gaseous and liquid fuels, in which case the

NULL

Document Number: NL ISO 15614 3 : 2018

Gives a non-exhaustive list of the botanical names and common names in English and French of plants or parts of plants used as spices or condiments. Replaces the first edition, which has been technically revised.

Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 3: Fusion welding of non-alloyed and low-alloyed cast irons

Sector: MANUFACTURING ENGINEERING

Document Number: NL ISO 15614 4 : 2018

This part of ISO 15614 specifies how a preliminary welding procedure specification (pWPS) for production and repair welding of non-alloyed and low-alloyed cast irons is qualified by fusion welding procedure tests. This part of ISO 15614 defines the conditions for execution of the welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of a defined list of variables. This part of ISO 15614 is applicable to all new welding procedures. However, it does not invalidate previous welding procedure tests made to former national standards or specifications. Where additional tests have to be carried out to make the qualification technically equivalent, it is only necessary to do the additional tests on a test piece made in accordance with this part of ISO 15614. Additional tests may be required by application standards. This part of ISO 15614 is applicable to welding non-alloyed and low-alloyed grey cast iron casting

Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 4: Finishing welding of aluminium castings

Sector: MANUFACTURING ENGINEERING

Document Number: NL ISO 5817 : 2018

This part of ISO 15614 is one of a series of standards, details of which are given in ISO 15607:2003, Annex A. It specifies how a welding procedure specification for finishing welding of aluminium castings is qualified by welding procedure tests. It does not apply to repair welding. For joint welding, ISO 15614-2 applies. Arc welding of aluminium castings is covered by the following processes as defined in ISO 4063: 131 metal inert gas welding, MIG welding; 141 tungsten inert gas arc welding; TIG welding; 15 plasma arc welding. Other fusion welding processes by agreement. Shielding gases used in these processes are:  argon ISO 14175 I1;  helium ISO 14175 I2;  argon-helium mixture ISO 14175 I3. Other shielding gases by agreement.

Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections

Sector: MANUFACTURING ENGINEERING

Document Number: NL ISO 10245 1 : 2018

This International Standard provides quality levels of imperfections in fusion-welded joints (except for beam welding) in all types of steel, nickel, titanium and their alloys. It applies to material thickness ≥ 0,5 mm. It covers fully penetrated butt welds and all fillet welds. Its principles can also be applied to partial-penetration butt welds. (Quality levels for beam welded joints in steel are presented in ISO 13919-1.) Three quality levels are given in order to permit application to a wide range of welded fabrication. They are designated by symbols B, C and D. Quality level B corresponds to the highest requirement on the finished weld. Several types of loads are considered, e.g. static load, thermal load, corrosion load, pressure load. Additional guidance on fatigue loads is given in Annex C. The quality levels refer to production and good workmanship. This International Standard is applicable to a) non-alloy and alloy steels, b) nickel and nickel alloys, c) titanium and titanium

Cranes -- Limiting and indicating devices -- Part 1: General

Sector: MATERIALS HANDLING EQUIPMENT

Document Number: NL ISO 10245 2 : 2018

This part of ISO 10245 specifies general requirements for limiting and indicating devices for cranes that are applicable to loads and motions, performance and environment. These devices restrict operation and/or provide the operator or other persons with operational information. The specific requirements for the various types of crane are given in the other parts of ISO 10245. It is emphasized that the safe and reliable operation of limiters and indicators depends upon regular inspection and maintenance.

Cranes -- Limiting and indicating devices -- Part 2: Mobile cranes

Sector: MATERIALS HANDLING EQUIPMENT

Document Number: NL ISO 15614 1 : 2018

This part of ISO 10245 specifies the requirements for devices which limit and/or indicate the loads, motions, performance, and environment of mobile cranes. The general requirements for limiting and indicating devices for cranes are given in ISO 10245-1. This part of ISO 10245 applies to all mobile cranes as defined in ISO 4306-2. See 4.1 and also 4.2. NOTE Some basic machine types within this scope are convertible for use in excavating work and other applications not considered to be lifting service. The requirements of this part of ISO 10245 are applicable to such machines

Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1:Arc and gas welding of steels and arc welding of nickel and nickel alloys

Sector: Manufacturing engineering