Document Number:
NL ISO 18674 2 : 2020
Sector:
Construction Materials and Building
Status:
C
Production Year:
2020
Price:
50000.0000
This document specifies the measurement of displacements along a line by means of extensometers carried out for geotechnical monitoring. General rules of performance monitoring of the ground, of structures interacting with the ground, of geotechnical fills and of geotechnical works are presented in ISO 18674-1. If applied in conjunction with ISO 18674-3, this document allows the determination of displacements acting in any direction. This document is applicable to: — monitoring the behaviour of soils, fills and rocks; — checking geotechnical designs in connection with the Observational Design procedure; — deriving geotechnical key parameters (e.g. from results of pile load tests or trial tunnelling); — evaluating stability ahead of, during or after construction (e.g. stability of natural slopes, slope cuts, embankments, excavation walls, foundations, dams, refuse dumps, tunnels). NOTE This document fulfils the requirements for the performance monitoring of the ground, of structures interacting with the ground and of geotechnical works by the means of extensometers as part of the geotechnical investigation and testing in accordance with References [5] and [6].
Document Number:
NL ISO 15985 : 2019
Sector:
Rubber and plastic industries
Status:
C
Production Year:
2019
Price:
25000.0000
ISO 15985 specifies a method for the evaluation of the ultimate anaerobic biodegradability of plastics based on organic compounds under high-solids anaerobic-digestion conditions by measurement of evolved biogas at the end of the test. This method is designed to simulate typical anaerobic digestion conditions for the organic fraction of mixed municipal solid waste. The test material is exposed in a laboratory test to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste. The anaerobic decomposition takes place under high-solids (more than 20 % total solids) and static non-mixed conditions. The test method is designed to yield the percentage of carbon in the test material and its rate of conversion to evolved carbon dioxide and methane (biogas).
Document Number:
NL ISO 16929 : 2019
Sector:
Rubber and plastic industries
Status:
C
Production Year:
2019
Price:
25000.0000
This International Standard is used to determine the degree of disintegration of plastic materials in a pilot-scale aerobic composting test under defined conditions. It forms part of an overall scheme for the evaluation of the compostability of plastics as outlined in ISO 17088. The test method laid down in this International Standard can also be used to determine the influence of the test material on the composting process and the quality of the compost obtained. It cannot be used to determine the aerobic biodegradability of a test material. Other methods are available for this (e.g. see ISO 14851, ISO 14852 or ISO 14855-1 and ISO 14855-2.
Document Number:
NL ISO 20200 : 2019
Sector:
Rubber and plastic industries
Status:
C
Production Year:
2019
Price:
25000.0000
ISO 20200specifies a method of determining the degree of disintegration of plastic materials when exposed to a laboratory-scale composting environment. The method is not applicable to the determination of the biodegradability of plastic materials under composting conditions. Further testing is necessary to be able to claim compostability.
Document Number:
NL ISO 9927 1 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
35000.0000
ISO 9927 specifies the general requirements for inspections to be carried out on cranes as defined in ISO 4306‑1. Additional requirements for particular types of cranes are intended to be covered by the relevant specific parts of ISO 9927.
Document Number:
NL ISO 9927 3 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
35000.0000
This part of ISO 9927 specifies the regular inspections to be carried out on tower cranes. It is intended to be used in conjunction with ISO 9927-1. It does not cover inspection prior to the first use of a tower crane.
Document Number:
NL ISO 9374 1 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
15000.0000
This standard Specifies generally the information to be provided by the purchaser and the manufacturer so that the most suitable crane can be supplied for the duty requirements and service conditions. Refers to ISO 4301-1 und ISO 7363.
Document Number:
NL ISO 9374 3 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
35000.0000
ISO 9374-3 gives guidance for information to be provided: a) by the purchaser when enquiring for a tower crane, b) by the purchaser when ordering a tower crane, c) by a manufacturer when offering (tendering) for a tower crane, d) by the manufacturer when supplying a tower crane.
Document Number:
NL ISO 9374 4 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
25000.0000
This standard Specifies information to be provided by a purchaser in enquiring for or ordering a jib crane and by a manufacturer in tendering for or supplying this crane. Annex A gives a format for information to be provided by the purchaser.
Document Number:
NL ISO 9100 9 : 2019
Sector:
Packaging and Distribution of Goods
Status:
C
Production Year:
2019
Price:
25000.0000
This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm deep for wide-mouth glass containers.
Document Number:
NL ISO 9100 10 : 2019
Sector:
Packaging and Distribution of Goods
Status:
C
Production Year:
2019
Price:
25000.0000
This document specifies the dimensions of a vacuum lug finish with a nominal size of 77 mm regular for widemouth glass containers.
Document Number:
NL 241 : 2019
Sector:
Food Technology
Status:
C
Production Year:
2019
Price:
25000.0000
تسري هذه المواصفة على المنتجات المعرف عنها في القسم 2 والمعروضة للاستهلاك المباشر، بما في ذلك لأغراض التموين أو لإعادة التعبئة اذا دعت الحاجة. وتشمل هذه المواصفة على سبيل المثال لا لاحصر المنتجات التالية: البصل، الثوم، المانجو، الفجل، الزنجبيل، الشمندر، الخوخ الملكي، الفلفل، قلب النخيل، الملفوف، الخس، الليمون، الذرة الصغيرة (اليافعة) والخردل الأخضر.. وهي لا تسري على المنتج اذا كان سيخضع لمزيد من التجهيز ولا تشمل هذه المواصفة كذلك الكمتشي وزيتون المائدة والساور كروات وصلصة شاتني والمقبلات.
Document Number:
NL EN 14073 2 : 2019
Sector:
Domestic and Commercial Equipment. Entertainment.
Status:
C
Production Year:
2019
Price:
0
This document specifies safety requirements for office storage furniture. This document does not apply to high density mechanized filing systems, rotary filing systems or plan files. It should be understood that fulfilling the specified requirements does not ensure that failure will not occur as a result of habitual misuse or after an excessively long period of service. Safety depending on structure of the building is not included e.g.: the strength of wall hanging cabinets includes only the cabinet and its parts. The wall and wall attachment are not included. Assessment of ageing is not included.
Document Number:
NL EN 527 1 : 2019
Sector:
Domestic and Commercial Equipment. Entertainment.
Status:
C
Production Year:
2019
Price:
35000.0000
This European Standard specifies dimensions of work tables and desks for office tasks to be undertaken in a seated, a sit stand or standing position. It includes neither dimensions for storage unit nor those for other tables in the office area or reception desks.
Document Number:
NL EN 1176 11 : 2019
Sector:
Domestic and commercial Equipment. Entertainment.S
Status:
C
Production Year:
2019
Price:
25000.0000
This European Standard specifies additional safety requirements for spatial networks intended for permanent installation for use by children. This European Standard is not applicable to artificial climbing structures, which are used for training for sports activities, e.g. alpinism.
Document Number:
NL EN 16051 2 : 2019
Sector:
FLUID SYSTEMS AND COMPONENTS FOR GENERAL USE
Status:
C
Production Year:
2019
Price:
25000.0000
This document specifies the interface geometry between valves and pump adapters as well as flow rate performance, pressure, marking and labelling for air pumps for inflatable consumer articles (see definition in 3.1). This document does not apply to: - valves of personal flotation devices according to EN ISO 12402; - diving accessories and buoyancy compensators according to EN 1809. This document excludes the following valve types: - valves used for bicycles and vehicles; - needle valves (e. g. valves used for team sport balls).
Document Number:
NL EN 1729 2 : 2019
Sector:
Domestic and commercial Equipment. Entertainment.S
Status:
C
Production Year:
2019
Price:
35000.0000
This European Standard specifies safety requirements and test methods for chairs and tables for general educational purposes in educational institutions. It applies to furniture for use with laptop computers or portable devices, but not to special purpose workstations, e.g. laboratories, ranked seating and workshops. Annex A (normative) includes a test method for the drop test of chairs. With the exception of Annex A, the figures illustrate test principles only and cannot be used to carry out the tests. NOTE EN 1729 1 specifies functional dimensions and marking of chairs and tables for general educational purposes.
Document Number:
NL EN 1957 : 2019
Sector:
Domestic and commercial Equipment. Entertainment.S
Status:
C
Production Year:
2019
Price:
25000.0000
This European standard specifies test methods for the determination of the durability and hardness of mattresses and all types of fully erected beds with mattresses (and mattress pads when they form a unit with the mattress). It does not apply to water beds, air beds and children cots. It includes a method for the determination of the firmness rating of a mattress or a bed correlating to the subjective assessment made by people (see Annex A). It must be emphasized that the firmness rating cannot be used to demonstrate comfort and/or quality of a mattress or a complete bed. Ageing and degradation caused by air, light, humidity and temperature is not included. The test results are only valid for the article tested. When test results are intended to be applied to other similar articles, the test specimen shall be representative of them.
Document Number:
NL EN 1730 : 2019
Sector:
Domestic and commercial Equipment. Entertainment.S
Status:
C
Production Year:
2019
Price:
35000.0000
This European Standard specifies test methods for the determination of stability, strength and durability of the structure of all types of tables and desks without regard to use, materials, design/construction or manufacturing process. This European Standard does not apply to changing units which are covered by other European Standards. Test methods for the assessment of ageing, degradation, and electrical functions are not included. This European Standard does not apply to the strength and durability of any storage features that are covered by other European Standards. This European Standard does not include any requirements. Requirements for different end uses can be found in other Standards.
Document Number:
NL ISO 20795 1 : 2019
Sector:
Health Care Technology
Status:
C
Production Year:
2019
Price:
35000.0000
ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements. It further specifies requirements with respect to packaging and marking the products and to the instructions to be supplied for use of these materials. Furthermore, it applies to denture base polymers for which the manufacturer claims that the material has improved impact resistance. It also specifies the respective requirement and the test method to be used. ISO 20795-1:2013 applies to denture base polymers such as those listed below: poly(acrylic acid esters); poly(substituted acrylic acid esters); poly(vinyl esters); polystyrene; rubber modified poly(methacrylic acid esters); polycarbonates; polysulfones; poly(dimethacrylic acid esters); polyacetals (polyoxymethylene); copolymers or mixtures of the polymers listed in 1 to 9.
Document Number:
NL ISO 20795 2 : 2019
Sector:
Health Care Technology
Status:
C
Production Year:
2019
Price:
35000.0000
ISO 20795-2:2013 is applicable to orthodontic base polymers and copolymers used in the construction of both active and passive orthodontic appliances and specifies their requirements. It also specifies test methods to be used in determining compliance with these requirements. It further specifies requirements with respect to packaging and marking the products and to the instructions to be supplied for use of these materials.
Document Number:
NL ISO 21563 : 2019
Sector:
Health Care Technology
Status:
C
Production Year:
2019
Price:
50000.0000
ISO 21563:2013 specifies the requirements and tests for helping determine whether the elastic aqueous agar and alginate hydrocolloid dental impression materials, as prepared for retail marketing, are of the quality needed for their intended purposes. It also specifies requirements for labelling and instructions for use.
Document Number:
NL ISO 22112 : 2019
Sector:
Health Care Technology
Status:
C
Production Year:
2019
Price:
35000.0000
ISO 22112:2017 specifies the classification, requirements, and test methods for artificial teeth such as ceramic teeth and polymer teeth that are industrially manufactured for use in dental prostheses.
Document Number:
NL ISO 22674 : 2019
Sector:
Health Care Technology
Status:
C
Production Year:
2019
Price:
50000.0000
ISO 22674:2016 classifies metallic materials that are suitable for the fabrication of dental restorations and appliances, including metallic materials recommended for use either with or without a ceramic veneer, or recommended for both uses, and specifies their requirements. Furthermore, it specifies requirements with respect to packaging and marking the products and to the instructions to be supplied for the use of these materials, including products delivered for sale to a third party. ISO 22674:2016 does not apply to alloys for dental amalgam (ISO 24234), dental brazing materials (ISO 9333), or metallic materials for orthodontic appliances (ISO 15841) (e.g. wires, brackets, bands and screws).
Document Number:
NL ISO 28319 : 2019
Sector:
Health Care Technology
Status:
C
Production Year:
2019
Price:
25000.0000
ISO 28319:2018 specifies requirements and test methods for laser welding and the filler materials thereto used in the dental laboratory for welding of metallic restorations and appliances. For filler materials used in laser welding, this document also specifies the information given in the instructions for use, marking and labelling.
Document Number:
NL ISO 17088 : 2019
Sector:
Rubber and Plastics Industries
Status:
C
Production Year:
2019
Price:
25000.0000
This International Standard specifies procedures and requirements for the identification and labelling of plastics, and products made from plastics, that are suitable for recovery through aerobic composting. The four following aspects are addressed: a) biodegradation; b) disintegration during composting; c) negative effects on the composting process and facility; d) negative effects on the quality of the resulting compost, including the presence of high levels of regulated metals and other harmful components. This specification is intended to establish the requirements for the labelling of plastic products and materials, including packaging made from plastics, as “compostable” or “compostable in municipal and industrial composting facilities” or “biodegradable during composting” (for the purposes of this International Standard, these three expressions are considered to be equivalent). The labelling will, in addition, have to conform to all international, regional, national or local regulations (e.g. European Directive 94/62/EC). NOTE The recovery of compostable plastics through composting can be carried out under the conditions found in well-managed composting plants, where the temperature, water content, aerobic conditions, carbon/nitrogen ratio and processing conditions are optimized. Such conditions are generally obtained in industrial and municipal composting plants. Under these conditions, compostable plastics will disintegrate and biodegrade at rates comparable to yard trimmings, kraft paper bags and food scraps.
Document Number:
NL ISO 17422 : 2019
Sector:
Rubber and Plastics Industries
Status:
C
Production Year:
2019
Price:
25000.0000
This document provides a structure for inclusion of environmental aspects in standards for plastics products. It proposes an approach which is directed at minimizing any adverse environmental impact without detracting from the primary purpose of ensuring adequate fitness for use of the products under consideration. The guidance provided by this document is intended primarily for use by standards writers. Over and above its primary purpose, however, this document provides guidance of value to those involved in design work and other activities where environmental aspects of plastics are being considered. NOTE This document is intended to promote the following practices: a) the use of techniques for identifying and assessing the environmental impact of technical provisions in standards, and for minimizing their adverse effects; b) the adoption of good practices such as: 1) procedures for pollution avoidance, e.g. through end-of-life options and its proper management; 2) material and energy conservation in the light of the intended use (and foreseeable misuse) of the product; 3) safe use of hazardous substances; 4) avoidance of technically unjustifiable restrictive practices; 5) promotion of performance criteria rather than exclusion clauses such as are based, for example, only on chemical composition criteria; 6) use of renewable resources and minimization of the use of non-renewable resources, if the life cycle assessment shows favourable; c) the adoption of a balanced approach in standards development to issues such as environmental impact, product function and performance, health and safety, and other regulatory requirements; d) the regular review and revision of existing standards in the light of technical innovations, permitting improvement in the environmental impact of products and processes; e) the application of life cycle analytical approaches wherever applicable and technically justifiable.
Document Number:
NL ISO 11994 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
35000.0000
This International Standard establishes generally accepted terms and definitions relating to availability of all types of cranes as defined in ISO 4306-1 with the aim of making contracts and mutual understanding easier. The terms and definitions are to be used by crane designers, manufacturers, inspecting authorities, users and others.
Document Number:
NL ISO 7363 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
25000.0000
This International Standard establishes the form of presentation and content of the documents which a manufacturer should provide with cranes and Iifting appliances (hereafter called “equipment”). Such documents give technical information and include acceptance documents for the equipment to facilitate its installation, testing and use. Specimen acceptance documents are given in the annex.
Document Number:
NL ISO 7296 1 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
35000.0000
This part of ISO 7296 establishes general graphic Symbols for use on the controls of cranes (section 2) and indicates colour for control buttons and Signal lamps (section 3). The Symbols are divided into the following groups given in 2.1, 2.2 and 2.3: 2.1 Symbols for basic directions of motion and on/off positions 2.2 Symbols for Operator controls 2.3 Information Symbols
Document Number:
NL ISO 7296 2 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
35000.0000
This part of ISO 7296 establishes graphical Symbolsfor use on Operator controls and other displays on mobile cranes as defined in ISO 4306-2.
Document Number:
NL ISO 7296 3 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
35000.0000
This part of ISO 7296 establishes graphical symbols for use on operator controls and other displays on tower cranes as defined in ISO 4306-3. Annex A gives examples for the combination of symbols.
Document Number:
NL ISO 9942 1 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
25000.0000
This part of ISO 9942 specifies the minimum requirements for labels for the identification (marking) and the operation of cranes.
Document Number:
NL 86 : 2019
Sector:
PAINT AND COLOUR INDUSTRIES
Status:
C
Production Year:
2019
Price:
25000.0000
1.1. This standard is for a white pigmented, latex-based primer-sealer intended for use on new and old interior plaster, concrete and wall board surfaces that are to be subsequently painted with a latex or alkyd finish coat. This coating is not intended for use on wood. 1.2. The primer sealer complying with this standard is intended for use on unpainted interior surfaces including gypsum board, plaster, smooth concrete and previously painted porous surfaces that are subsequently to be painted with an alkyd or latex finish. This primer sealer should not be used on previous coatings with gloss or semi-gloss finishes. This material is not intended for use as a finish coat or on woods prone to extractive bleeding (i.e. cedar) where a stain blocking primer is required. 1.3. This primer sealer is not intended to fill or bridge gaps or holes in concrete or concrete block surfaces where block filler would be more suitable. 1.4. This primer sealer is not intended to be used on metals or anot
Document Number:
NL ISO 8566 2 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
25000.0000
This part of ISO 8566 establishes the criteria for cabins for mobile cranes as defined in ISO 4306-2. These criteria are intended to cover cabins only for crane operation and not for road travel. The general criteria for cabins on mobile cranes are presented in ISO 8566-1.
Document Number:
NL ISO 12210 1 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
15000.0000
This part of ISO 12210 establishes the general criteria for the provision of anchoring devices for cranes and crane parts for in-service and out-of-service conditions. Other parts of ISO 11210 present the requirements for specific crane types.
Document Number:
NL ISO 12210 4 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
25000.0000
This part of ISO 12210 provides specific requirements for anchoring devices for in-service and out-of-service conditions for jib cranes as defined in ISO 4306-1, other than tower cranes, mobile cranes and railway cranes that are otherwise generally covered by other parts of ISO 12210.
Document Number:
NL ISO 11629 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
25000.0000
This International Standard sets forth basic procedures for measuring the mass of a cranes as a whole and/or of its components. This International Standard was prepared in addition to ISO 4310 and covers the types of cranes as defined in ISO 4306-1.
Document Number:
NL ISO 4310 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
25000.0000
This International Standard specifies tests, inspections and procedures for verifying the conformance of a crane with its operational specifications and its capability to lift rated loads (see ISO 7363). This International Standard is applicable to the types of cranes designated in ISO 4306-1, prior to first use following manufacture or after modification or repair of the load-bearing structure or a component of an individual crane. Where rated loads are governed by stability, a test procedure and test load are specified that permit stability margins to be easily verified.
Document Number:
NL ISO 14518 : 2019
Sector:
materials handling equipment
Status:
C
Production Year:
2019
Price:
25000.0000
This International Standard establishes — methods for composition and measurement of test loads; — procedures for the application of test loads during the testing of cranes. This International Standard was developed in addition to ISO 4310 and covers the types of cranes described in ISO 4306-1.
Document Number:
NL 795 : 2019
Sector:
Chemical Technology
Status:
C
Production Year:
2019
Price:
50000.0000
تحدّد هذه المواصفة الق اٌس ةٌ اللبنان ةٌ )م.ق.ل. 3526:966 ( القواعد الت جٌب لأي مستحضر تجم لٌ متاح ف السوق اللبنان الامتثال بها من أجل ضمان س رٌ عمل السوق المحلّ ومستوى عال من حما ةٌ صحة الإنسان. تشمل هذه المواصفة : - المعلومات الت جٌب ذكرها على بطاقة المعلومات الب اٌن ةٌ الت تلصق أو تطبع على عبوات مستحضرات التجم لٌ أو ترفق بها على اختلاؾ أحجام هذه العبوات وأشكالها. - المواد الممنوع إضافتها. - المواد المق دٌ استعمالها. - المواد الملونة المسموح استعمالها. - المواد الحافظة المسموح أو المق دٌ استعمالها. - المواد المرشحة للأشعة فوق البنفسج ةٌ المسموح استعمالها.
Document Number:
NL EN 12953 4 : 2019
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2019
Price:
35000.0000
This European Standard specifies requirements for the workmanship and construction of shell boilers as defined in EN 12953-1. NOTE 1 For other components such as water tube walls, see the EN 12952 series. NOTE 2 For economizers and superheaters, see EN 12953-4 or EN 12952-5.
Document Number:
NL EN 12953 5 : 2019
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2019
Price:
35000.0000
This Part of the European Standard specifies requirements for the inspection during construction, documentation and marking of shell boilers as defined in EN 12953-1.