Document Number:
NL EN 14085 : 2017
Sector:
Domestic and Commercial Equipment. Entertainment.
Status:
C
Production Year:
2017
Price:
35000.0000
This European Standard specifies requirements and test methods for floor panels, which have surface layers consisting of resilient floor covering. The floor panels are considered suitable for domestic and commercial levels of use. This European Standard is not applicable to floor panels that are subject to frequent wetting, such as bathrooms, laundry rooms and saunas. This European Standard also specifies the requirements for marking and packaging.
Document Number:
NL EN 14565 : 2017
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2017
Price:
35000.0000
This European Standard specifies the characteristics for resilient floor coverings based upon synthetic thermoplastic polymers, supplied either in roll or tile form. This specification does not apply to floor coverings specified in the series EN 649 to EN 654.
Document Number:
NL ISO 10595 : 2017
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2017
Price:
25000.0000
This International Standard specifies the characteristics of semi-flexible/vinyl composition floor tiles based on poly(vinyl chloride) (PVC) binder and supplied in tile form. Products may contain a transparent, non-PVC factory finish. To encourage the consumer to make an informed choice, this International Standard includes a classification system (see ISO 10874) based on the intensity of use, which shows where these floor coverings give satisfactory service. It also specifies requirements for marking.
Document Number:
NL ISO 24011 : 2017
Sector:
Domestic and Commercial Equipment. Entertainment.
Status:
C
Production Year:
2017
Price:
25000.0000
This International Standard specifies the characteristics of plain and decorative linoleum, supplied as either tiles or rolls. To encourage the consumer to make an informed choice, this International Standard includes a classification system based on the intensity of use, which shows where resilient floor coverings provide satisfactory service. The term 'linoleum' is frequently incorrectly applied to a range of floor coverings, often to those based on poly(vinyl chloride) or rubber. Such materials are not included in this International Standard.
Document Number:
NL ISO 26986 : 2017
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2017
Price:
25000.0000
This International Standard specifies the characteristics of floor coverings based on expanded (cushioned) poly(vinyl chloride), supplied as either tiles or rolls. This International Standard includes a classification system based on the intensity of use, which shows where resilient floor coverings give satisfactory service.
Document Number:
NL EN 1081 : 2017
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2017
Price:
25000.0000
This document specifies test methods for determining: a) the vertical resistance, b) the resistance to earth, c) the surface resistance of a resilient, laminate and modular multilayer floor covering after installation in test piece or after installation.
Document Number:
NL EN 1815 : 2017
Sector:
textile and leather technology
Status:
C
Production Year:
2017
Price:
25000.0000
This standard specifies a method for determining the body voltage generated when a person wearing standardized footwear walks on a resilient or laminate floor covering. The test method can be used under laboratory conditions as well as in situ.
Document Number:
NL ISO 26987 : 2017
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2017
Price:
25000.0000
This International Standard specifies a procedure for the determination of the reaction of resilient floor covering to chemical substances.
Document Number:
NL ISO 770 : 2017
Sector:
chemical technology
Status:
C
Production Year:
2017
Price:
25000.0000
This International Standard specifies certain characteristics of the raw and rectified oils of Eucalyptus globulus (Eucalyptus globulus Labill.), in order to facilitate assessment of its quality.
Document Number:
NL ISO 855 : 2017
Sector:
chemical technology
Status:
C
Production Year:
2017
Price:
25000.0000
This International Standard specifies certain characteristics of the oil of lemon [Citrus limon (L.) Burm. f.], obtained by expression, in order to facilitate assessment of its quality.
Document Number:
NL ISO 856 : 2017
Sector:
Chemical Technology
Status:
C
Production Year:
2017
Price:
25000.0000
This International Standard specifies certain characteristics of the oil of peppermint (Mentha × piperita L.), with a view to facilitate assessment of its quality. NOTE As it is difficult to differentiate the specification of peppermint oils (Mentha × piperita L.) from different origins, they have been regrouped in this International Standard. The following origins have been taken into consideration: USA, United Kingdom, France, Italy, India and China.
Document Number:
NL ISO 12917 1 : 2017
Sector:
PETROLEUM AND RELATED TECHNOLOGIES
Status:
C
Production Year:
2017
Price:
50000.0000
This document specifies manual methods for the calibration of nominally horizontal cylindrical tanks, installed at fixed locations. The methods in this document are applicable to insulated and non-insulated tanks, either when they are above-ground or underground. The methods are applicable to pressurized tanks and to both knuckle-dish-end and flat-end cylindrical tanks as well as elliptical and spherical head tanks. This document is applicable to tanks inclined from the horizontal, provided a correction is applied for the measured tilt. Although this document does not impose any limits on the maximum tank diameter and maximum tank tilt to which this document is applicable, the practical limits would be about 4 m in diameter and 10° in tilt.
Document Number:
NL ISO 12917 2 : 2017
Sector:
PETROLEUM AND RELATED TECHNOLOGIES
Status:
C
Production Year:
2017
Price:
25000.0000
This part of ISO 12917 specifies a method for the calibration of horizontal cylindrical tanks having diameters greater than 2 m by means of internal measurements using an electro-optical distance-ranging instrument, and for the subsequent compilation of tank-capacity tables. This method is known as the internal electro-optical distance-ranging (EODR) method. This part of ISO 12917 is applicable to tanks inclined by up to 10 % from the horizontal, provided a correction is applied for the measured tilt.
Document Number:
NL ISO 19840 : 2017
Sector:
PAINT AND COLOUR INDUSTRIES
Status:
C
Production Year:
2017
Price:
35000.0000
This International Standard specifies a procedure for the verification of dry-film thickness against nominal dry film thickness on rough surfaces, including the adjustment of the instruments used, the definition of inspection areas, sampling plans, measurement methods and acceptance/rejection criteria. For the purposes of this standard, any specified thickness is taken to be nominal as defined in ISO 12944‑5, and the dry-film thickness is the typical thickness above the peaks of the surface profile. The procedure described in this International Standard is based on the use of instruments of the permanent magnet, electromagnet and eddy current type. Instrument accuracy is verified both at zero and at a known thickness on a smooth surface and adjusted if necessary. Measurements taken on a coating on a roughened steel substrate will therefore be higher than the actual value above the peaks of the profile. The thickness of the dry film above the peaks of the profile is defined as the instrument reading minus an appropriate correction value. The dry-film thickness is obtained by using the appropriate correction value applied to readings based on adjustment on a smooth, flat steel surface. Where individual readings, based on adjustment on a smooth, flat steel surface without the use of correction values, are specified or agreed, it is important to recognize that this method does not conform with this International Standard. This standard is applicable if the nominal dry-film thickness is 40 μm or greater. NOTE If the nominal thickness is less than the surface roughness of the substrate, the uncertainty of the measurement will increase.
Document Number:
NL EN 61427 1 : 2017
Sector:
ENERGY AND HEAT TRANSFER ENGINEERING
Status:
C
Production Year:
2017
Price:
25000.0000
IEC 61427-1:2013 is part of a series which gives general information relating to the requirements for the secondary batteries used in photovoltaic energy systems (PVES) and to the typical methods of test used for the verification of battery performances. This part deals with cells and batteries used in photovoltaic off-grid applications. This standard is applicable to all types of secondary batteries.
Document Number:
NL EN 61427 2 : 2017
Sector:
ELECTRICAL ENGINEERING
Status:
C
Production Year:
2017
Price:
50000.0000
IEC 61427-2:2015 relates to secondary batteries used in on-grid Electrical Energy Storage (EES) applications and provides the associated methods of test for the verification of their endurance, properties and electrical performance in such applications. The test methods are essentially battery chemistry neutral, i.e. applicable to all secondary battery types. On-grid applications are characterized by the fact that batteries are connected, via power conversion devices, to a regional or nation- or continent-wide electricity grid and act as instantaneous energy sources and sinks to stabilize the grids performance when randomly major amounts of electrical energy from renewable energy sources are fed into it. Related power conversion and interface equipment is not covered by this part of IEC 61427.
Document Number:
NL EN 61850 7 420 : 2017
Sector:
TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING
Status:
C
Production Year:
2017
Price:
50000.0000
IEC 61850-7-420 defines IEC 61850 information models to be used in the exchange of information with distributed energy resources (DER), which comprise dispersed generation devices and dispersed storage devices, including reciprocating engines, fuel cells, microturbines, photovoltaics, combined heat and power, and energy storage. Utilizes existing IEC 61850-7-4 logical nodes where possible, but also defines DER-specific logical nodes where needed.
Document Number:
NL HD 60364 7 712 : 2017
Sector:
ENERGY AND HEAT TRANSFER ENGINEERING
Status:
C
Production Year:
2017
Price:
25000.0000
IEC 60364-7-712:2017 RLV contains both the official IEC International Standard and its Redline version. The Redline version is not an official document, it is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition. IEC 60364-7-712:2017 applies to the electrical installation of PV systems intended to supply all or part of an installation. The equipment of a PV installation, like any other item of equipment, is dealt with only so far as its selection and application in the installation is concerned. This new edition includes significant revisions and extensions, taking into account experience gained in the construction and operation of PV installations, and developments made in technology, since the first edition of this standard was published.
Document Number:
NL EN 13108 1 : 2017
Sector:
Construction Materials and Building
Status:
C
Production Year:
2017
Price:
50000.0000
This European Standard specifies requirements for mixtures of the mix group Asphalt Concrete for use on roads, airfields and other trafficked areas. Asphalt Concrete is used for surface courses, binder courses, regulating courses, and bases. The mixtures of the mix group Asphalt Concrete are produced on the basis of hot bitumen. Mixtures utilizing bitumen emulsion and bituminous materials based on in situ recycling are not covered by this standard. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21.
Document Number:
NL EN 13108 2 : 2017
Sector:
Construction Materials and Building
Status:
C
Production Year:
2017
Price:
35000.0000
This European Standard specifies requirements for mixtures of the mix group Asphalt Concrete for Very Thin Layers for use on roads, airfields and other trafficked areas. Asphalt Concrete for Very Thin Layers is a bituminous material, of which the composition and the grading of the aggregate is selected for application of the material in very thin layers with a thickness of 20 mm to 30 mm. Mixtures utilizing bitumen emulsion and bituminous materials based on in situ recycling are not covered by this standard. Asphalt Concrete for Very Thin Layers is used for surface courses. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21
Document Number:
NL EN 13108 3 : 2017
Sector:
Construction Materials and Building
Status:
C
Production Year:
2017
Price:
35000.0000
This European Standard specifies requirements for mixtures of the mix group Soft Asphalt for use on low volume roads and roads with low stability. Soft Asphalt is used for surface courses, regulating courses and bases in colder climates. The mixtures of the mix group Soft Asphalt are produced on the basis of hot bitumen. Mixtures utilizing bitumen emulsion and bituminous materials based on in situ recycling are not covered by this standard. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21.
Document Number:
NL EN 13108 4 : 2017
Sector:
Construction Materials and Building
Status:
C
Production Year:
2017
Price:
35000.0000
This European Standard specifies requirements for mixtures of the mix group Hot Rolled Asphalt for use on roads, airfields and other trafficked areas. Hot Rolled Asphalt is used for surface courses, binder courses, regulating courses and bases. The mixtures of the mix group Hot Rolled Asphalt are produced on the basis of hot bitumen. Mixtures utilizing bitumen emulsion and bituminous materials based on in situ recycling are not covered by this standard. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21.
Document Number:
NL ISO 3033 1 : 2017
Sector:
chemical technology
Status:
C
Production Year:
2017
Price:
25000.0000
This part of ISO 3033 specifies certain characteristics of the oil of spearmint, native type (Mentha spicata L.), in order to facilitate assessment of its quality.
Document Number:
NL ISO 3033 2 : 2017
Sector:
chemical technology
Status:
C
Production Year:
2017
Price:
25000.0000
This part of ISO 3033 specifies certain characteristics of the oil of spearmint, Chinese type (80 % and 60 %) (Mentha viridis L. var. crispa Benth.), redistilled oil, in order to facilitate assessment of its quality.
Document Number:
NL ISO 3033 3 : 2017
Sector:
chemical technology
Status:
C
Production Year:
2017
Price:
25000.0000
This part of ISO 3033 specifies certain characteristics of the oil of spearmint, Indian type (Mentha spicata L.), redistilled oil, in order to facilitate assessment of its quality.
Document Number:
NL 761 : 2017
Sector:
Food Technology
Status:
C
Production Year:
2017
Price:
50000.0000
1.1 FOOD ADDITIVES INCLUDED IN THIS STANDARD Only the food additives listed herein are recognized as suitable for use in foods in conformance with the provisions of this Standard. 1 Only food additives that have been assigned an Acceptable Daily Intake (ADI) or determined, on the basis of other criteria, to be safe2 by the Joint FAO/WHO Expert Committee on Food Additives (JECFA)3 and an International Numbering System (INS) designation by Codex will be considered for inclusion in this Standard. The use of additives in conformance with this Standard is considered to be technologically justified. 1.2 FOODS IN WHICH ADDITIVES MAY BE USED This Standard sets forth the conditions under which food additives may be used in all foods, whether or not they have previously been standardized by Codex. The use of additives in foods standardized by Codex is subject to the conditions of use established by the Codex commodity standards and this Standard. The General Standard for Food Additives (GSFA) should be the single authoritative reference point for food additives. Codex commodity committees have the responsibility and expertise to appraise and justify the technological need for the use of additives in foods subject to a commodity standard. The information given by the commodity committees may also be taken into account by the Codex Committee on Food Additives (CCFA) when considering food additive provisions in similar non-standardized foods. When a food is not covered by a commodity committee, CCFA will appraise the technological need. 1.3 FOODS IN WHICH ADDITIVES MAY NOT BE USED Food categories or individual food items in which the use of food additives is not acceptable, or where use should be restricted, are defined by this Standard. 1.4 MAXIMUM USE LEVELS FOR FOOD ADDITIVES The primary objective of establishing maximum use levels for food additives in various food groups is to ensure that the intake of an additive from all its uses does not exceed its ADI. The food additives covered by this Standard and their maximum use levels are based in part on the food additive provisions of previously established Codex commodity standards, or upon the request of governments after subjecting the requested maximum use levels to an appropriate method for verifying the compatibility of a proposed maximum level with the ADI. Annex A of this Standard may be used as a first step in this regard. The evaluation of actual food consumption data is also encouraged.
Document Number:
NL EN 13108 7 : 2017
Sector:
Construction Materials and Building
Status:
C
Production Year:
2017
Price:
35000.0000
This European Standard specifies requirements for mixtures of the mix group Porous Asphalt for use on roads, airfields and other trafficked areas. NOTE A mixture specification derived from this European Standard can be used either to declare the conformity of a mixture with known requirements or to make known what those requirements are. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21. Porous Asphalt mixtures with chemical modified binders not covered by EN 14023 are not covered by this European Standard.
Document Number:
NL EN 13877 1 : 2017
Sector:
Construction Materials and Building
Status:
C
Production Year:
2017
Price:
25000.0000
This European Standard specifies requirements for: the constituents (concrete and other materials) of concrete pavements; the properties of fresh and hardened concrete. This European Standard is applicable to concrete pavements cast in situ. Concrete compacted by rollers is not covered by this European Standard. This European Standard covers concrete pavements for roads, motorways and airports, pedestrian footpaths, cycle tracks, storage areas, and in general all traffic-bearing structures.
Document Number:
NL ISO 1342 : 2017
Sector:
chemical technology
Status:
C
Production Year:
2017
Price:
25000.0000
This International Standard specifies certain characteristics of the essential oil of rosemary (Rosmarinus officinalis L.), in order to facilitate assessment of its quality.
Document Number:
NL ISO TR 14049 : 2017
Sector:
Construction Materials and Building
Status:
C
Production Year:
2017
Price:
50000.0000
This Technical Specification provides the requirements and a structure for a data documentation format, to be used for transparent and unambiguous documentation and exchange of Life Cycle Assessment (LCA) and Life Cycle Inventory (LCI) data, thus permitting consistent documentation of data, reporting of data collection, data calculation and data quality, by specifying and structuring relevant information. The data documentation format specifies requirements on division of data documentation into data fields, each with an explanatory description. The description of each data field is further specified by the structure of the data documentation format. This Technical Specification is applicable to the specification and structuring of questionnaire forms and information systems. However, it can also be applied to other aspects of the management of environmental data. This Technical Specification does not include requirements on completeness of data documentation. The data documentation format is independent of any software or database platform for implementation. This Technical Specification does not require any specific sequential, graphic or procedural solutions for the presentation or treatment of data, nor does it describe specific modelling methodologies for LCI and LCA data
Document Number:
NL 251 : 2016
Sector:
Chemical Technology
Status:
C
Production Year:
2016
Price:
15000.0000
تحدد هذه المواصفة القياسية المتطلبات الواجب توافرها في صابون الزينة المعد على شكل قطع للاستعمال في أغراض نظافة الجسم.
Document Number:
NL 147 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
15000.0000
This standard specifies the conditions for fire protection in buildings intended for residential, educational, commercial, healthcare, hotels, furnished apartments, industrial occupations, warehouses, car garage and high-rise-non residential buildings.
Document Number:
NL 753 : 2016
Sector:
Petroleum and related Technologies
Status:
C
Production Year:
2016
Price:
25000.0000
تحدد هذه المواصفة القياسية المتطلبات العامة الواجب توافرها في البنزين الممتاز 98 أوكتان بدون رصاص والمعد للاستعمال كوقود في المركبات ذات محركات الاحتراق الداخلي بما فيها المركبات المزودة بوسائل تخفيف انبعاث الملوثات
Document Number:
NL ISO 8068 : 2016
Sector:
Petroleum and related Technologies
Status:
C
Production Year:
2016
Price:
35000.0000
This International Standard specifies the minimum requirements for turbine lubricants, as delivered. It specifies the requirements for a wide variety of turbines for power generation, including steam turbines, gas turbines, combined-cycle turbines with a common lubrication system and hydraulic (water driven) turbines. This International Standard does not specify the requirements for wind turbines, which are dealt with in ISO 12925-1[4]. Whilst power generation is the primary application for turbines, steam and gas turbines can also be used to drive rotating equipment, such as pumps and compressors. The lubrication systems of these driven loads can be common to that of the turbine. Turbine installations incorporate complex auxiliary systems requiring lubrication, including hydraulic systems, gearboxes and couplings. Depending upon the design and configuration of the turbine and driven equipment, turbine lubricants can also be used in these auxiliary systems. This International Standard should be read in conjunction with ISO 6743-5[2], the classification of different turbine lubricant types. The following lubricants are considered in this International Standard: — mineral oils; — synthetic lubricants, ester and polyalphaolefin types intended for high-temperature gas turbines; — synthetic lubricants, ester and polyalphaolefin types, environmentally acceptable for use in hydraulic turbines; — fire-resistant phosphate-ester type lubricants. NOTE For the purposes of this International Standard, the term “% (m/m)” is used to represent the mass fraction.
Document Number:
NL ISO 11158 : 2016
Sector:
Petroleum and related Technologies
Status:
C
Production Year:
2016
Price:
25000.0000
This International Standard specifies the minimum requirements for new mineral oil hydraulic fluids and is intended for hydraulic systems, particularly for hydrostatic hydraulic fluid power application. The purpose of this International Standard is for the guidance of suppliers and end users of mineral oil hydraulic fluids and for the direction of equipment manufacturers of hydraulic systems. This International Standard is written in a general form so that its application can accommodate various climatic conditions throughout the world. This International Standard also stipulates the requirements for mineral-oil hydraulic fluids at the time of delivery. Classification of fluids used in hydraulic applications is defined in ISO 6743-4. Of the categories covered by ISO 6743-4, only five types of mineral oil based fluids are covered in this International Standard. These categories are HH, HL, HM, HV and HG.
Document Number:
NL EN 13707 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard specifies definitions and characteristics for flexible reinforced bitumen sheets for which the intended use is roofing. This covers sheets used as top layers, intermediate layers and underlayers. It does not cover reinforced bitumen sheets for waterproofing used as underlays for discontinuous roofing. This European Standard does not cover waterproofing sheets which are intended to be used fully bonded under bituminous products (e.g. asphalt) directly applied at high temperature, specified by EN 14695.
Document Number:
NL EN 13859 1 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European standard specifies the characteristics of flexible sheets for underlays which are to be used under roof covering of discontinuous roofs. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.
Document Number:
NL EN 13859 2 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European standard specifies the characteristics of flexible sheets for underlays for walls which are to be used in walls behind outside wall coverings in order to avoid penetration of wind and water from outside. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.
Document Number:
NL EN 13984 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard specifies the characteristics of flexible sheets of plastic or rubber intended for use as water vapour control layers for buildings and applies to both reinforced and unreinforced products. It specifies requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
Document Number:
NL EN 13956 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard specifies the definitions and characteristics of plastic and rubber sheets including sheets made out of their blends and alloys (thermoplastic rubber) for which the intended use is roof waterproofing. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard. NOTE For typical materials and applications, see Annex E
Document Number:
NL EN 13967 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This document specifies definitions and characteristics of flexible plastic and rubber sheets which are intended to be used as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods, and provides for the evaluation of conformity of the products with the requirements of this standard.
Document Number:
NL EN 14909 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard specifies the characteristics of flexible sheets of plastics and rubber intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard. This European Standard does not cover related products such as preformed cavity trays, coping and flashings
Document Number:
NL ISO 1248 : 2016
Sector:
PAINT AND COLOUR INDUSTRIES
Status:
C
Production Year:
2016
Price:
35000.0000
This International Standard specifies the requirements and the corresponding methods of test for all manufactured and natural iron oxide pigments, in dry form, suitable for general use. These pigments are identified by Colour Index Nos.1) red 101 and 102, yellow 42 and 43, brown 6 and 7 and black 11, and includes “rapid-dispersion pigments”. This International Standard does not cover micaceous iron oxide pigments (see Note 1), transparent iron oxide pigments, granular grey iron oxide (see Note 2) or magnetic iron oxide pigments other than those of Colour Index Pigment black 11. NOTE 1 The requirements and the corresponding methods of test for micaceous iron oxide pigments are specified in ISO 10601. NOTE 2 Granular grey iron oxides are too abrasive for general use.
Document Number:
NL ISO 4621 : 2016
Sector:
Paint and colour industries
Status:
C
Production Year:
2016
Price:
25000.0000
This International Standard specifies the requirements and corresponding methods of test for chrome Oxide green Pigments suitable for general use.
Document Number:
NL ISO 591 1 : 2016
Sector:
Paint and colour industries
Status:
C
Production Year:
2016
Price:
25000.0000
This part of ISO 591 specifies the requirements and corresponding methods of test for titanium dioxide pigments for paints.
Document Number:
NL ISO 2495 : 2016
Sector:
Paint and colour industries
Status:
C
Production Year:
2016
Price:
25000.0000
This International Standard specifies the requirements and the corresponding methods of test for iron blue Pigments.
Document Number:
NL EN 13413 : 2016
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2016
Price:
25000.0000
This European Standard specifies the characteristics of floor coverings with compact surface layers, made of polyvinyl chloride and modifications thereof, on a filled fibrous backing and supplied in roll form. To encourage the consumer to make an informed choice, the standard includes a classification system (see EN 685) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirement for marking.
Document Number:
NL EN 13553 : 2016
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2016
Price:
25000.0000
This European standard specifies the minimum additional characteristics which are necessary for: - polyvinyl chloride floor coverings in roll form according to EN ISO 10581 or EN ISO 10582, - polyvinyl chloride floor coverings with foam backing in roll form to EN 651, - polyvinyl chloride floor coverings with particle based enhanced slip resistance in roll form to EN 13845 to be installed satisfactorily in special wet areas to form a watertight installation with a long life. It specifies two categories (A and B) for use on different substrates.
Document Number:
NL EN 651 : 2016
Sector:
Domestic and Commercial Equipment. Entertainment.
Status:
C
Production Year:
2016
Price:
25000.0000
This European Standard specifies the characteristics of floor coverings based on polyvinyl chloride with polyvinyl chloride foam layer, supplied in either tile or roll form. To encourage the consumer to make an informed choice, the standard includes a classification system (see EN 685) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking.
Document Number:
NL EN 13845 : 2016
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2016
Price:
25000.0000
This European Standard specifies the characteristics of floor coverings with sustainable enhanced slip resistant characteristics under specified conditions based on polyvinyl chloride and modifications thereof, supplied in either tile or roll form. To encourage the consumer to make an informed choice, this European Standard includes a classification system (see EN 685) based on intensity of use, which shows where resilient floor coverings should give satisfactory service. In addition, this European Standard details the requirements for the information to be included on the packaging labels. The slip measurements are made in a laboratory on ex-factory floor covering surfaces only. The method described is suitable for testing on wet surfaces.