Document Number:
NL ISO 6743 11 : 2016
Sector:
Petroleum and related Technologies
Status:
C
Production Year:
2016
Price:
15000.0000
This part of ISO 6743 establishes the detailed classification of lubricants of family P for pneumatic tools and machines driven by compressed air. All the lubricants listed belong to class L (Lubricants, industrial oils and related products). This classification System covers only lubricants which are in contact with the compressed air. Pneumatic tools or machinery may have other Points of lubrication (e.g. internal bearings, gears, etc.) which are not covered by this part of ISO 6743. This classification applies only for normal operational and environmental conditions. If abnormal conditions are encountered, e.g. very high or very low temperatures, the manufacturer of the equipment and/or the supplier of the lubricant should be consulted. This part of ISO 6743 should be read in conjunction with ISO 6743-0.
Document Number:
NL ISO 6743 12 : 2016
Sector:
Petroleum and related Technologies
Status:
C
Production Year:
2016
Price:
15000.0000
This part of IS0 6743 establishes the detailed classification of family 0 (heat transfer fluids). All products listed belong to class L (Lubricants, industrial oils and related products). This part of IS0 6743 should be read in conjunction IS0 6743-O.
Document Number:
NL EN 61730 1 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
35000.0000
This part of IEC 61730 pertains to the particular requirements of construction. IEC 61730-2 defines the requirements for testing. This International Standard series lays down IEC requirements of terrestrial photovoltaic modules suitable for long-term operation in open-air climates. This standard is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. PV modules covered by this standard are limited to a maximum DC system voltage of 1 500 V. This International Standard defines the basic requirements for various applications of PV modules, but it cannot be considered to encompass all national or regional codes. Specific requirements, e.g. for building, marine and vehicle applications, are not covered. This International Standard does not address specific requirements for products that combine a PV module with power conversion equipment, monitoring or control electronics, such as integrated inverters, converters or output disabling functions. While parts of this standard may be applicable to flat plate PV modules with internally generated low level concentration below 3 times, it was not written specifically to address these concerns. This International Standard is designed to coordinate with the test sequences in the IEC 61215 series, so that a single set of samples may be used to perform both the safety and qualification of a photovoltaic module design. The object of this International Standard is to define the requirements for the construction of photovoltaic modules with respect to safety. These requirements are intended to minimize the misapplication and misuse of PV modules or the failure of their components which could result in fire, electric shock and personal injury. Additional construction requirements outlined in relevant ISO standards, or the national or local codes which govern the installation and use of these PV modules in their intended locations, should be considered in addition to the requirements contained within this standard.
Document Number:
NL EN 61730 2 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
50000.0000
The scope of IEC 61730-1 is also applicable to this part of IEC 61730. While IEC 61730-1 outlines the requirements of construction, this part of the standard lists the tests a PV module is required to fulfill for safety qualification. IEC 61730-2 is applied for safety qualification only in conjunction with IEC 61730-1. The sequence of tests required in this standard may not test for all possible safety aspects associated with the use of PV modules in all possible applications. This standard utilizes the best sequence of tests available at the time of its writing. There are some issues - such as the potential danger of electric shock posed by a broken PV module in a high voltage system - that should be addressed by the system design, location, restrictions on access and maintenance procedures. The objective of this standard is to provide the testing sequence intended to verify the safety of PV modules whose construction has been assessed by IEC 61730-1. The test sequence and pass criteria are designed to detect the potential breakdown of internal and external components of PV modules that would result in fire, electric shock, and/or personal injury. The standard defines the basic safety test requirements and additional tests that are a function of the PV module end-use applications. Test categories include general inspection, electrical shock hazard, fire hazard, mechanical stress, and environmental stress The additional testing requirements outlined in relevant ISO standards, or the national or local codes which govern the installation and use of these PV modules in their intended locations, should be considered in addition to the requirements contained within this standard.
Document Number:
NL EN 62109 1 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
50000.0000
This part of IEC 62109 applies to the power conversion equipment (PCE) for use in Photovoltaic (PV) systems where a uniform technical level with respect to safety is necessary. This standard defines the minimum requirements for the design and manufacture of PCE for protection against electric shock, energy, fire, mechanical and other hazards. This standard provides general requirements applicable to all types of PV PCE. There are additional parts of this standard that provide specific requirements for the different types of power converters, such as Part 2 – inverters. Additional parts may be published as new products and technologies are commercialised.
Document Number:
NL EN 62109 2 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
35000.0000
This Part 2 of IEC 62109 covers the particular safety requirements relevant to d.c. to a.c. inverter products as well as products that have or perform inverter functions in addition to other functions, where the inverter is intended for use in photovoltaic power systems. Inverters covered by this standard may be grid-interactive, stand-alone, or multiple mode inverters, may be supplied by single or multiple photovoltaic modules grouped in various array configurations, and may be intended for use in conjunction with batteries or other forms of energy storage. Inverters with multiple functions or modes shall be judged against all applicable requirements for each of those functions and modes. NOTE Throughout this standard where terms such as "grid-interactive inverter" are used, the meaning is either a grid-interactive inverter or a grid-interactive operating mode of a multi-mode inverter This standard does not address grid interconnection requirements for grid-interactive inverters.
Document Number:
NL EN 62116 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
35000.0000
The purpose of this International Standard is to provide a test procedure to evaluate the performance of islanding prevention measures used with utility-interconnected PV systems. This standard describes a guideline for testing the performance of automatic islanding prevention measures installed in or with single or multi-phase utility interactive PV inverters connected to the utility grid. The test procedure and criteria described are minimum requirements that will allow repeatability. Additional requirements or more stringent criteria may be specified if demonstrable risk can be shown. Inverters and other devices meeting the requirements of this standard are considered non-islanding as defined in IEC 61727. This standard may be applied to other types of utility-interconnected systems (e.g. inverterbased microturbine and fuel cells, induction and synchronous machines). However, technical review may be necessary for other than inverter-based PV systems.
Document Number:
NL ISO IEC 27033 1 : 2016
Sector:
Information Technology. Office Machines
Status:
C
Production Year:
2016
Price:
50000.0000
ISO/IEC 27033-1:2009 provides an overview of network security and related definitions. It defines and describes the concepts associated with, and provides management guidance on, network security. (Network security applies to the security of devices, security of management activities related to the devices, applications/services and end-users, in addition to security of the information being transferred across the communication links.) It is relevant to anyone involved in owning, operating or using a network. This includes senior managers and other non-technical managers or users, in addition to managers and administrators who have specific responsibilities for information security and/or network security, network operation, or who are responsible for an organization's overall security program and security policy development. It is also relevant to anyone involved in the planning, design and implementation of the architectural aspects of network security. ISO/IEC 27033-1:2009 also p
Document Number:
NL EN 54 26 : 2016
Sector:
ENVIRONMENT. HEALTH PROTECTION. SAFETY
Status:
C
Production Year:
2016
Price:
50000.0000
This European Standard specifies requirements, test methods and performance criteria for point detectors using carbon monoxide sensing for use in fire detection and fire alarm systems in and around buildings (see EN 54-1:2011). This European Standard provides for the assessment and verification of consistency of performance (AVCP) of carbon monoxide point detectors to this EN. This European Standard does not apply to fire detectors incorporating at least one CO sensing element in combination with other elements sensing different fire phenomena. CO detectors having special characteristics suitable for the detection of specific fire risks are not covered by this European Standard. The performance requirements for any additional functions are beyond the scope of this European Standard (e.g. additional features or enhanced functionality for which this standard does not define a test or assessment method).
Document Number:
NL EN 1634 3 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This Part of EN 1634 specifies a method for determining the leakage of cold and warm smoke from one side of a door assembly to the other under the specified test conditions. The test can be applied to door and shutter assemblies of different types intended for purposes of controlling the passage of smoke in case of fire. This test can also be applied to lift landing doors and conveyor system doors and shutters. The principle of the test is explained d) safety during transport, installation, repairs and dismantling of accessible goods only lifts; e) the use of translucent material for the walls of the well and machinery spaces, for the load carrying unit and for the landing doors with the exception of their vision panels; f) the use of programmable electronic systems in safety related applications for lifts (PESSRAL). However, this European Standard may usefully be taken as guidance where relevant. 1.6 This European Standard is not applicable to accessible goods only lifts which were manufactured before the date of its publication as EN. 1.7 The significant hazards, hazardous situations and events dealt with by this standard are those listed in EN ISO 14121-1:2007, Annex A (see Clause 4) with the exception of: - noise; - vibration; - fire; - any form of radiation except EMC.briefly in annex A.
Document Number:
NL EN 15288 1 : 2016
Sector:
Domestic and commercial equipment. Entertainment.
Status:
C
Production Year:
2016
Price:
35000.0000
This document specifies safety requirements relevant to certain aspects of the design and construction of classified pools according to Clause 4. It is intended for those concerned with the design, construction, planning and operation of classified swimming pools. It provides guidance about the risks associated by identifying the design characteristics required for a safe environment. The requirements of this document are applicable to all new classified pools and, as appropriate, to specific refurbishments of classified existing pools. This document has limited application to classified pools which consist of segregated areas of rivers, lakes or the sea but this document should be followed where relevant. National and/or local legislation may apply. This document is not applicable to domestic swimming pools according to EN 16582 (all parts). Further definitions of domestic swimming pools and/or use are given in EN 16582.
Document Number:
NL ISO TR 14069 : 2016
Sector:
Environment. Health protection. Safety
Status:
C
Production Year:
2016
Price:
50000.0000
This Technical Report describes the principles, concepts and methods relating to the quantification and reporting of direct and indirect greenhouse gas (GHG) emissions for an organization. It provides guidance for the application of ISO 14064-1 to greenhouse gas inventories at the organization level, for the quantification and reporting of direct emissions, energy indirect emissions and other indirect emissions. This Technical Report describes for all organizations, including local authorities, the steps for: — establishing organizational boundaries, in accordance with either a control approach (financial or operational) or an equity share approach; — establishing operational boundaries, by identifying direct emissions and energy indirect emissions to be quantified and reported, as well as any other indirect emissions the organization chooses to quantify and report; for each category of emission, guidance is provided on specific boundaries and methodologies for the quantification of GHG emissions and removals; — GHG reporting: guidance is provided to promote transparency regarding the boundaries, the methodologies used for the quantification of direct and indirect GHG emissions and removals, and the uncertainty of the results. A table of correspondence between the numbering of ISO 14064-1:2006 and this Technical Report is provided in Annex A. The examples and case studies presented in this Technical Report are not exclusive and non-exhaustive. The values of the emission or removal factors mentioned in the examples are given for illustrative purposes only. A non-exhaustive list of database references is provided in Annex B.
Document Number:
NL ISO TS 14033 : 2016
Sector:
Environment. Health protection. Safety
Status:
C
Production Year:
2016
Price:
50000.0000
This Technical Specification supports the application of standards and reports on environmental management. It provides guidelines on how to acquire quantitative environmental information and data and implement methodology. It gives guidelines to organizations on general principles, policy, strategy and activities necessary to obtain quantitative environmental information for internal and/or external purposes. Such purposes can be, for example, to establish inventory routines and support decision making related to environmental policies and strategies, aimed in particular at comparing quantitative environmental information. The information is related to organizations, activities, facilities, technologies or products. This Technical Specification addresses issues related to defining, collecting, processing, interpreting and presenting quantitative environmental information. It provides guidelines on how to establish accuracy, verifiability and reliability for the intended use. It utilizes proven and well-established approaches for the preparation of information adapted to the specific needs of environmental management. It is applicable to all organizations, regardless of their size, type, location, structure, activities, products, level of development and whether or not they have an environmental management system in place. This Technical Specification supplements the contents of other International Standards on environmental management. NOTE Annex A provides illustrative guidelines, examples of how to apply the guidelines and case studies with examples.
Document Number:
NL ISO TS 14067 : 2016
Sector:
Environment. Health protection. Safety
Status:
C
Production Year:
2016
Price:
50000.0000
This Technical Specification specifies principles, requirements and guidelines for the quantification and communication of the carbon footprint of a product (CFP), based on International Standards on life cycle assessment (ISO 14040 and ISO 14044) for quantification and on environmental labels and declarations (ISO 14020, ISO 14024 and ISO 14025) for communication. Requirements and guidelines for the quantification and communication of a partial carbon footprint of a product (partial CFP) are also provided. This Technical Specification is applicable to CFP studies and different options for CFP communication based on the results of such studies. Where the results of a CFP study are reported according to this Technical Specification, procedures are provided to support both transparency and credibility and also to allow for informed choices. This Technical Specification also provides for the development of CFP-product category rules (CFP-PCR), or the adoption of product category rules (PCR) that have been developed in accordance with ISO 14025 and that are consistent with this Technical Specification. This Technical Specification addresses only one impact category: climate change. Offsetting is outside of the scope of this Technical Specification.
Document Number:
NL ISO TS 14072 : 2016
Sector:
Environment. Health protection. Safety
Status:
C
Production Year:
2016
Price:
35000.0000
This Technical Specification (TS) provides additional requirements and guidelines for an effective application of ISO 14040 and ISO 14044 to organizations. This Technical Specification details - the application of Life Cycle Assessment (LCA) principles and methodology to organizations, - the benefits that LCA can bring to organizations by using LCA methodology at organizational level, - the system boundary, - specific considerations when dealing with LCI, LCIA, and interpretation, and - the limitations regarding reporting, environmental declarations, and comparative assertions. This Technical Specification applies to any organization that has interest in applying LCA. It is not intended for the interpretation of ISO 14001 and specifically covers the goals of ISO 14040 and ISO 14044.
Document Number:
NL EN 60891 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
35000.0000
defines procedures to be followed for temperature and irradiance corrections to the measured I-V (current-voltage) characteristics of photovoltaic devices. It also defines the procedures used to determine factors relevant for these corrections. Requirements for I-V measurement of photovoltaic devices are laid down in IEC 60904-1. The main technical changes with regard the previous edition are as follows: - extends edition 1 translation procedure to irradiance change during I-V measurement; - adds 2 new translation procedures; - revises procedure for determination of temperature coefficients to include PV modules; - defines new procedure for determination of internal series resistance; - defines new procedure for determination of curve correction factor.
Document Number:
NL EN 60904 3 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
25000.0000
This part of IEC 60904 applies to the following photovoltaic devices for terrestrial applications: - solar cells with or without a protective cover; - sub-assemblies of solar cells; - modules; and - systems. NOTE The term "test specimen" is used to denote any of these devices. The principles contained in this standard cover testing in both natural and simulated sunlight. Photovoltaic conversion is spectrally selective due to the nature of the semiconductor materials used in PV solar cells and modules. To compare the relative performance of different PV devices and materials a reference standard solar spectral distribution is necessary. This standard includes such a reference solar spectral irradiance distribution. This standard also describes basic measurement principles for determining the electrical output of PV devices. The principles given in this standard are designed to relate the performance rating of PV devices to a common reference terrestrial solar spectral irradiance distribution. The reference terrestrial solar spectral irradiance distribution is given in this standard in order to classify solar simulators according to the spectral performance requirements contained in IEC 60904-9.
Document Number:
NL EN 61683 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
35000.0000
Describes guidelines for measuring the efficiency of power conditioners used in stand-alone and utility-interactive photovoltaic systems, where the output of the power conditioner is a stable a.c. voltage of constant frequency or a stable d.c. voltage.
Document Number:
NL EN 62509 : 2016
Sector:
Energy and Heat transfer Engineering
Status:
C
Production Year:
2016
Price:
35000.0000
IEC 62509:2010 establishes minimum requirements for the functioning and performance of battery charge controllers (BCC) used with lead acid batteries in terrestrial photovoltaic systems. The main aims are to ensure BCC reliability and to maximise the life of the battery.
Document Number:
NL ISO 22715 : 2016
Sector:
Chemical Technology
Status:
C
Production Year:
2016
Price:
25000.0000
This International Standard specifies requirements for packaging and labelling of all cosmetic products as defined according to national regulations or practices intended for sale or free distribution. National regulations can, on several points, be more strict than this International Standard. This International Standard is intended for use on cosmetics. NOTE For packaging and labelling of toothpastes and oral rinses, see also ISO 11609 and ISO 16408 .
Document Number:
NL EN 124 6 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard applies to manhole tops and gully tops made of Polypropylene (PP), Polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) by a moulding or extrusion process, with a clear opening up to and including 1 000 mm for covering gullies, manholes and inspection chambers for installation within areas subjected to pedestrian and/or vehicular traffic. It is applicable to manhole tops and gully tops for use in - areas which can only be used by pedestrians and pedal cyclists (class A 15), and - pedestrian areas and comparable areas, car parks or car parking decks (class B 125). This European Standard gives guidance for combinations of covers/grating made of PP, PE or PVC–U with frames according to EN 124 2, EN 124 3, EN 124 4 and EN 124 5. This European Standard is not applicable in isolation but only in combination with EN 124 1. This European Standard is not applicable to: - rodding point covers according to EN 13598 1; - gratings/covers as part of prefabricated drainage channels according to EN 1433; - floor and roof gullies in buildings which are specified in EN 1253 (all parts); - surface boxes
Document Number:
NL EN TS 14472 1 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
25000.0000
This Technical Specification gives recommendations for the installation of resilient, textile and laminate floor coverings in new or existing buildings. It describes procedures in design, installation and maintenance which are in use throughout Europe for all floor covering materials and highlights the major differences that may exist in different national procedures. The guidelines in this Technical Specification are intended for use in cases where manufacturer's instructions, taking account of the national code of practice in the country where the installation is to be made, are not available. References to the national codes that are currently available are listed in the bibliography of the various parts of this Technical Specification. All parts of the Technical Specification are intended to supplement, and not conflict with, National Standards.
Document Number:
NL EN TS 14472 2 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This Technical Specification provides recommendations for the installation of textile floor coverings. It covers all products composed of textile material with a pile or non-pile use surface, and includes the laying of carpet tiles (excluding rugs). It details suitable methods of installation and advises on the selection of the materials required for their implementation. The guidelines in this Technical Specification are intended for use in cases where manufacturer's instructions, taking account of the national code of practice in the country where the installation is to be made, are not available. References to the national codes that are currently available are listed in the bibliography of the various parts of this Technical Specification. This Part 2 of the Technical Specification is intended for use in conjunction with Part 1 that deals with general matters relevant to resilient and laminate floor coverings as well as textile floor coverings. All parts of the Technical Specification are intended to supplement and not conflict with national standards.
Document Number:
NL ISO 6743 13 : 2016
Sector:
Petroleum and related Technologies
Status:
C
Production Year:
2016
Price:
25000.0000
This part of ISO 6743 establishes the detailed classification of family G (lubricants for slideways). All the lubricants listed in this classification belong to class L (Lubricants, industrial oils and related products). This part should be read in conjunction with ISO 6743-99.
Document Number:
NL ISO 6743 14 : 2016
Sector:
Petroleum and related Technologies
Status:
C
Production Year:
2016
Price:
25000.0000
This part of IS0 6743 establishes the detailed classification of hardening fluids of family U for use in the field of heat treatment. All the fluids listed belong to class L (lubricants, industrial oils and related products) rn This part of IS0 6743 is intended to provide a standardized code for the identification of lubricants and related products used in the process of hardening metallic materials. It should be read in conjunction with IS0 6743-O. This family is divided into several large product categories according to the different applications involved.
Document Number:
NL ISO 6743 15 : 2016
Sector:
Petroleum and related Technologies
Status:
C
Production Year:
2016
Price:
25000.0000
This part of ISO 6743 establishes the detailed classification, in tabular form, of engine lubricating oils for us ing the following internal combustion engines: a) two-stroke cycle, spark-ignition gasoline engines that employ a crank case scavenging system and are used in transportation, leisure and utility applications, such as motorcycles, snow mobiles, chainsaws (hereinafter referred to as two-stroke engine oils); b) four-stroke cycle, spark-ignition gasoline engines that employ a common sump containing the lubricant for both the engine and the drive train/starter/transmission of motorcycles, motor scooters, all-terrain vehicles (ATVs) and related equipment (hereinafter referred to as four-stroke engine oils). Outboard motor and marine engine applications are described in Annex A. It is expected that this part of ISO 6743 be read in conjunction with ISO 6743-99.
Document Number:
NL EN 81 22 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
50000.0000
1.1 This European Standard specifies the safety rules for the construction and installation of permanently installed new electric lifts, with traction or positive drive, serving defined landings levels, having a vehicle designed to convey passengers or passengers and loads, suspended by ropes or chains and travelling in a vertical plan along guide rails that are inclined at an angle of between 15° and 75° in relation to the horizontal. 1.2 In addition to the requirements of this standard, supplementary requirements should be considered in special cases (potentially explosive atmosphere, extreme climate conditions, seismic conditions, transporting dangerous goods, etc.). 1.3 This European Standard does not cover: a) lifts with drives other than those stated in 1.1; b) installation of electric lifts in existing buildings to the extent that space does not permit; c) important modifications (see Annex E) to a lift installed before this standard is brought into application; d) lifting appliances, such as paternosters, mine lifts, theatrical lifts, appliances with automatic caging, skips, lifts and hoists for building and public works sites, ships' hoists, platforms for exploration or drilling at sea, construction and maintenance appliances; e) safety during transport, installation, repairs, and dismantling of lifts; f) lifts with rated speed ≤ 0,15 m/s. However, this standard may usefully be taken as a basis. Noise is not dealt with in this standard because it is not relevant to the safe use of the lift. Vibrations are dealt with for electric parts only. Direct effects on human bodies are not considered as harmful. 1.4 This European Standard does not specify the additional requirements necessary for the use of lifts in case of fire. 1.5 Taking into account the state of art, the scope of the present standard is limited as follows: — inclination: a variation in inclination is permitted for the travel path; — travel path: confined within the vertical plane; — maximum capacity of the car: 7 500 kg (100 passengers); — maximum rated speed (v): 4 m/s. Both characteristics (capacity and speed) are linked by the relation given in the following Figure 1.
Document Number:
NL ISO 14065 : 2016
Sector:
Construction materials and building
Status:
C
Production Year:
2016
Price:
35000.0000
This International Standard specifies principles and requirements for bodies that undertake validation or verification of greenhouse gas (GHG) assertions. It is GHG programme neutral. If a GHG programme is applicable, the requirements of that GHG programme
Document Number:
NL ISO 21931 1 : 2016
Sector:
Construction materials and building
Status:
C
Production Year:
2016
Price:
35000.0000
This part of ISO/TS 21931 provides a general framework for improving the quality and comparability of methods for assessing the environmental performance of buildings. It identifies and describes issues to be taken into account when using methods for the assessment of environmental performance for new or existing building properties in the design, construction, operation, refurbishment and deconstruction stages. The building is the object of the assessment defined in this part of ISO/TS 21931, and this encompasses the building itself, the site and the associated facilities on the site. It is recognized that environmental performance is only one of a number of significant factors in a building’s overall performance. This part of ISO/TS 21931 is intended be used in conjunction with, and following the principles set out in, the ISO 14000 series of International Standards.
Document Number:
NL ISO 14031 : 2016
Sector:
Construction materials and building
Status:
C
Production Year:
2016
Price:
50000.0000
This International Standard gives guidance on the design and use of environmental performance evaluation (EPE) within an organization. It is applicable to all organizations, regardless of type, size, location and complexity. This International Standard does not establish environmental performance levels. The guidance in this International Standard can be used to support an organization’s own approach to EPE, including its commitments to compliance with legal and other requirements, the prevention of pollution, and continual improvement. NOTE This International Standard is a generic standard and does not include guidance on specific methods for valuing or weighting different kinds of impacts in different kinds of sectors, disciplines, etc
Document Number:
NL ISO TR 14047 : 2016
Sector:
Construction materials and building
Status:
C
Production Year:
2016
Price:
50000.0000
The purpose of this Technical Report is to provide examples to illustrate current practice of life cycle impact assessment according to ISO 14044:2006. These examples are only a sample of all possible examples that could satisfy the provisions of ISO 14044. They offer "a way" or "ways" rather than the "unique way" of applying ISO 14044. They reflect the key elements of the life cycle impact assessment (LCIA) phase of the LCA. The examples presented in this Technical Report are not exclusive and other examples exist to illustrate the methodological issues described.
Document Number:
NL EN 1555 3 : 2016
Sector:
Fluid systems and components for general use
Status:
C
Production Year:
2016
Price:
35000.0000
This !European Standard" specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for piping systems in the field of the supply of gaseous fuels. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with Parts 1, 2, 4 and 5 of EN 1555, it is applicable to PE fittings, their joints and to joints with components of PE and other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1); b) an operating temperature of 20 °C as reference temperature. NOTE 1 For other operating temperatures, derating coefficients should be used; see EN 1555-5. EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. This European Standard is applicable for fittings of the following types: c) electrofusion socket fittings; d) electrofusion saddle fittings; e) spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion); f) mechanical fittings. The fittings can e.g. be in the form of couplers, equal and reduced tees, reducers, bends or caps.
Document Number:
NL EN 1555 4 : 2016
Sector:
Fluid systems and components for general use
Status:
C
Production Year:
2016
Price:
35000.0000
This part of EN 1555 specifies the characteristics of valves made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels. NOTE 1 Valves made from other material than polyethylene designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PE piping system according to EN 1555 provided they have relevant PE connection for butt fusion or electrofusion ends (see EN 1555-3). It also specifies the test parameters for the test methods referred to in this standard. In conjunction with Parts 1, 2, 3 and 5 of EN 1555, it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1); b) an operating temperature of 20 °C as reference temperature; NOTE 2 For other operating temperatures, derating coefficients should be used, see EN 1555-5. c) an operating temperature between -20 °C and +40 °C. EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It is applicable to bi-directional valves with spigot end or electrofusion socket intended to be fused with PE pipes conforming to EN 1555-2 without any fittings or with PE fittings conforming to EN 1555-3. This European Standard covers valves for pipes with a nominal outside diameter dn ≤ 315 mm.
Document Number:
NL EN 1555 5 : 2016
Sector:
Fluid systems and components for general use
Status:
C
Production Year:
2016
Price:
25000.0000
This part of EN 1555 specifies requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels. It specifies the definitions of electrofusion, butt fusion and mechanical joints. It specifies the method of preparation of test piece joints, and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It specifies the test parameters for the test methods referred to in this standard. In conjunction with Parts 1 to 4 of EN 1555, it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1); b) an operating temperature of 20 °C as reference temperature. NOTE 1 For other operating temperatures, derating coefficients should be used, see Annex A. EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
Document Number:
NL CEN TS 1555 7 : 2016
Sector:
Fluid systems and components for general use
Status:
C
Production Year:
2016
Price:
35000.0000
This Technical Specification gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 1555 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures. It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [2]. NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN 45011 [3], EN 45012 [4] or EN ISO/IEC 17020 [5], as applicable. In conjunction with Parts 1 to 5 of EN 1555 (see Foreword), this Technical Specification is applicable to polyethylene (PE) plastics piping systems for the supply of gaseous fuels. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar1); b) an operating temperature of 20 °C as reference temperature. NOTE 2 For other operating temperatures, derating coefficients can be used; see EN 1555-5. For mechanical fittings conforming to ISO 10838-1 [6], ISO 10838-2 [7] or ISO 10838-3 [8], as applicable, guidance for assessment of conformity is not given in this part of EN 1555. When requested, a quality plan based on the tests mentioned in ISO 10838-1 [6], ISO 10838-2 [7] or ISO 10838-3 [8], as applicable, should be set up in agreement between user and manufacturer. EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
Document Number:
NL EN 81 41 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
50000.0000
1.1 This European Standard deals with safety requirements for construction, manufacturing, installation, maintenance and dismantling of electrically powered vertical lifting platforms affixed to a building structure intended for use by persons with impaired mobility: travelling vertically between predefined levels along a guided path whose inclination to the vertical does not exceed 15°; intended for use by persons with or without a wheelchair; supported or sustained by rack and pinion, wire ropes, chains, screw and nut, friction/traction between wheels and the rail, guided chain, scissors mechanism or hydraulic jack (direct or indirect); with enclosed liftways; with a speed not greater than 0,15 m/s; with platforms where the carrier is not completely enclosed. 1.2 This standard deals with all significant hazards relevant to lifting platforms, when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). 1.3 This European Standard does not specify the additional requirements for: operation in severe conditions (e.g. extreme climates, strong magnetic fields); lightning protection; operation subject to special rules (e.g. potentially explosive atmospheres); handling of materials, the nature of which could lead to dangerous situations; vertical lifting platforms whose primary function is the transportation of goods; vertical lifting platforms whose carriers are completely enclosed; vertical lifting platforms prone to vandalism; hazards occurring during manufacture; earthquakes, flooding; fire fighting, evacuation and behaviour during a fire; noise and vibrations; the design of concrete, hardcore, timber or other foundation or building arrangement; the design of anchorage bolts to the supporting structure; type C wheelchairs as defined in EN 12183 and/or EN 12184. NOTE For the actual type of machinery, noise is not considered a significant nor relevant hazard. 1.4 This standard is not applicable to Vertical Lifting Platforms intended for use by persons with impaired mobility which are manufactured before the date of its publication as an EN.
Document Number:
NL EN 934 2 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard specifies definitions and requirements for admixtures for use in concrete. It covers admixtures for plain, reinforced and prestressed concrete which are used in site mixed, ready mixed concrete and precast concrete. The performance requirements in this standard apply to admixtures used in concrete of normal consistence. They may not be applicable to admixtures intended for other types of concrete such as semi-dry and earth moist mixes. Provisions governing the practical application of admixtures in the production of concrete, i.e. requirements concerning composition, mixing, placing, curing etc. of concrete containing admixtures are not part of this standard.
Document Number:
NL EN 934 3 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
25000.0000
This European Standard defines and specifies the requirements and conformity criteria for admixtures for use in cement based masonry mortar. It covers two types of admixtures, long term retarding and air entraining/plasticising which are used in ready-mixed and site made masonry mortars. Provisions for the use of admixtures for masonry mortar are not part of this European Standard but are covered by EN 998-1 and EN 998-2
Document Number:
NL EN 934 5 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard defines and specifies requirements and conformity for admixtures specifically intended for use in sprayed concrete. The types of admixtures covered are: set accelerating and non-alkaline set accelerating admixtures; consistence control admixtures; bond improving admixtures. Provisions governing the practical application of these admixtures in the production of sprayed concrete are not part of this European Standard
Document Number:
NL ISO 10406 1 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
50000.0000
This part of ISO 10406 specifies test methods applicable to fibre-reinforced polymer (FRP) bars and grids as reinforcements or pre-stressing tendons in concrete.
Document Number:
NL EN 61215 : 2016
Sector:
Electrical engineering
Status:
C
Production Year:
2016
Price:
50000.0000
This International Standard lays down IEC requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general openair climates, as defined in IEC 60721-2-1. It applies only to crystalline silicon modules types. A standard for thin-film modules has been published as IEC 61646. This standard does not apply to modules used with concentrated sunlight.
Document Number:
NL EN 61646 : 2016
Sector:
Electrical engineering
Status:
C
Production Year:
2016
Price:
35000.0000
This International Standard lays down requirements for the design qualification and type approval of terrestrial, thin-film photovoltaic modules suitable for long-term operation in general open-air climates as defined in IEC 60721-2-1. This standard is intended to apply to all terrestrial flat plate module materials not covered by IEC 61215. The test sequence is derived from IEC 61215 for the design qualification and type approval of terrestrial crystalline silicon PV modules. However, it no longer relies on meeting a plus/minus criterion before and after each test, but rather on meeting a specified percentage of the rated minimum power after all of the tests have been completed and the modules have been lightsoaked. This eliminates the technology-specific preconditioning necessary to accurately measure the changes caused by the test. This standard does not apply to modules used with concentrators.
Document Number:
NL CLC TS 61836 : 2016
Sector:
Electrical Engineering
Status:
C
Production Year:
2016
Price:
50000.0000
This Technical Specification deals with the terms and symbols from national and international solar photovoltaic standards and relevant documents used within the field of solar photovoltaic (PV) energy systems. It includes the terms and symbols compiled from the published IEC technical committee 82 standards, previously published as technical report IEC 61836:1997. The focus of this Technical Specification is "what do the words mean" and not "under what conditions do the terms apply".
Document Number:
NL EN 60904 1 : 2016
Sector:
Electrical Engineering
Status:
C
Production Year:
2016
Price:
25000.0000
This part of IEC 60904 describes procedures for the measurement of current-voltage characteristics of photovoltaic devices in natural or simulated sunlight. These procedures are applicable to a single photovoltaic solar cell, a sub-assembly of photovoltaic solar cells, or a PV module. NOTE 1 This standard may be applicable to multi-junction test specimens, if each sub-junction generates the same amount of current as it would under the reference AM1,5 spectrum in IEC 60904-3. NOTE 2 This standard may be applicable to PV devices designed for use under concentrated irradiation if they are irradiated using direct normal irradiance and a mismatch correction with respect to a direct normal reference spectrum is performed. The purpose of this standard is to lay down basic requirements for the measurement of current-voltage characteristics of photovoltaic devices, to define procedures for different measuring techniques in use and to show practices for minimising measurement uncertainty
Document Number:
NL ISO 11020 : 2016
Sector:
Chemical Technology
Status:
C
Production Year:
2016
Price:
25000.0000
This International Standard specifies certain characteristics of oil of turpentine, Iberian type (Pinus pinaster Sol.), in order to facilitate assessment of its quality.
Document Number:
NL ISO 21389 : 2016
Sector:
Chemical Technology
Status:
C
Production Year:
2016
Price:
25000.0000
This International Standard specifies certain characteristics of the oil of gum turpentine, Chinese (mainly from Pinus massoniana Lamb.), in order to facilitate assessment of its quality.
Document Number:
NL EN 14303 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard specifies the requirements for factory made mineral wool products, which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately 0 °C to + 800 °C. NOTE Below an operating temperature of ambient, special means against water vapour diffusion and water accumulation by air flow might be required. Below an operating temperature of - 50 °C, special tests regarding the suitability of the products in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured with or without facings or coatings, in the form of rolls, boards, slabs, mats, felts, quilts, wired mats, lamella mats, bevelled lags and pipe sections. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard. This Eurpean Standard does not cover products for in situ insulation (blowing or pouring) or products for the insulation of the building structure. This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.
Document Number:
NL EN 14304 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard specifies the requirements for factory made flexible elastomeric foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 200 °C to + 175 °C. NOTE Below an operating temperature of - 50 °C, tests regarding the suitability of the products in the intended application shall be performed. Manufacturer's advice should be heeded in all cases. The products are manufactured in the form of sheets, tubes, rolls and tapes with or without coating and/or self-adhesive backing and/or different closure systems. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,050 W/(m·K) at 10 °C are not covered by this standard. This European Standard does not cover products for the insulation of the building structure. The normative part of this standard does not cover compressive stress (see Annex D, D.5).
Document Number:
NL EN 14305 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
50000.0000
This European Standard specifies the requirements for factory made cellular glass products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 265 °C to + 430 °C. NOTE Below an operating temperature of - 50 °C, special tests regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured in the form of faced or unfaced boards, pipe sections, segments and prefabricated ware. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered. This standard does not specify the required level of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard. This standard does not cover products for the insulation of the building structure
Document Number:
NL EN 14306 : 2016
Sector:
Construction Materials and Building
Status:
C
Production Year:
2016
Price:
35000.0000
This European Standard specifies the requirements for factory made calcium silicate products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 170 °C to + 1 100 °C. NOTE Calcium silicate products can be used below - 50 °C. Below the operating temperature of - 50 °C, special tests, regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases. The products are manufactured in the form of boards, pipe sections, segments and prefabricated ware. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered. This standard does not specify the required level or class of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender. Products with a declared thermal conductivity greater than 0,6 W/(mK) at 10 °C are not covered by this standard. This standard does not cover products intended to be used for the insulation of the building structure. This standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.