Libnor | المعايير |

Document Number: NL EN 10025 6 : 2019

This European Standard applies only to condensing units for refrigeration and describes a number of selected performance test methods. These methods provide sufficiently accurate results for the determination of the refrigerating capacity, power absorbed, refrigerant mass flow and the coefficient of performance. This European Standard applies only to performance tests conducted at the manufacturer's works or wherever the instrumentation and load stability for testing to the accuracy required is available.

Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition

Sector: Metallurgy

Document Number: NL EN 12572 1 : 2019

Part 6 of this document, in addition to part 1, specifies requirements for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 2 to 4 (chemical composition) and Tables 5 to 7 (mechanical properties) and are supplied in the quenched and tempered condition as given in 6.3. The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness ≤ 150 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness ≤ 100 mm for grade S890 and a maximum nominal thickness ≤ 50 mm for grade S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa1) to 960 MPa1).

NULL

Sector: NULL

Document Number: NL EN 913 : 2019

NULL

Sector: NULL

Document Number: NL EN 1335 1 : 2019

NULL

Office furniture - Office work chair - Part 1: Dimensions -

Document Number: NL EN 1335 2 : 2019

This part of the prEN 1335:1999 applies to office work chairs. It specifies dimensions of three types of chairs as well as test methods for their determination.

Office furniture - Office work chair - Part 2: Safety requirements

Document Number: NL CEN TR 1335 4 : 2019

This document specifies safety, strength and durability requirements for office work chairs. It does not apply to other seating in the office area for which other European Standards exist. The requirements are based upon use for 8 h a day by persons weighing up to 110 kg. Annex A (informative) contains loads, masses and cycles for functional tests.

Office furniture - Office work chair - Part 4: Clarifications to EN

Document Number: NL ISO 15928 1 : 2019

This Technical Report specifies the definitions of a number of terms given in EN 1335-1:2000, which have been identified by CEN/TC 207/SC 3/WG 1 as being interpreted in different ways by test laboratories and manufacturers.

Houses — Description of performance — Part 1: Structural safety

Document Number: NL EN 1096 1 : 2019

This part of ISO 15928 sets out a method for describing the structural safety performance of houses. It covers objectives, provides performance descriptions, establishes parameter descriptions, and outlines evaluation processes. It includes a description of permanent, imposed, wind, seismic, snow and other actions as well as structural resistance. This part of ISO 15928 is intended for use in the evaluation of the design and construction of houses, in the international trading of houses or their sub-systems, and in developing risk-management tools for the protection of houses. The ISO 15928‑ series does not specify a level of performance and it is not intended to provide a design method and/or criteria. It describes the structural safety of a house as a whole. NOTE 1 Annex A includes background information on this part of ISO 15928, guidance on its use, and suggestions on good practice. NOTE 2 Details on references referred to in Notes are provided in a Bibliography. NOTE 3 Structural serviceability, durability and other attributes are covered in other parts of ISO 15928.

Glass in building - Coated glass - Part 1: Definitions and

Document Number: NL EN 12758 : 2019

This European Standard defines the characteristics, properties and classification of coated glass for use in building. Test methods and procedures used to establish durability are in Parts 2 and 3 of this standard. Factory production control and evaluation of conformity, including Annex ZA, are in Part 4 of this standard. Test methods for determination of self cleaning performances of coated glass are in Part 5. This standard applies to coated glass for glazing application for use in normally occupied domestic or commercial premises. This standard is not applicable to: - adhesive backed polymeric films on glass (prEN 15755-1); - mirrors made from silvered float glass (EN 1036-1); - enamelled glass (EN 12150-1, EN 1863-1, 14179-1). - Painted glass (standard in development)

Glass in building - Glazing and airborne sound insulation -

Document Number: NL EN 13313 : 2019

This European Standard assigns sound insulation values to all transparent, translucent and opaque glass products, described in the European Standards for basic, special basic or processed glass products, when intended to be used in glazed assemblies in buildings, and which exhibit properties of acoustic protection, either as a prime intention or as a supplementary characteristic. This document outlines the procedure, by which glass products may be rated, according to their acoustic performance which enables assessment of compliance with the acoustic requirements of buildings. Rigorous technical analysis of measurement data remains an option, but this standard is intended to enable the derivation of simpler indices of performance, which can be adopted with confidence by non-specialists. By adopting the principles of this standard the formulation of acoustic requirements in Building Codes and for product specification to satisfy particular needs for glazing is simplified. It is recognised that the acoustic test procedures contained within EN ISO 10140 relate only to glass panes and their combinations. Although the same principles should be followed as closely as possible, it is inevitable that some compromises are necessary, because of the bulkier construction of other glazing types, e.g. glass blocks, paver units, channel-shaped glass, structural glazing and structural sealant glazing. Guidelines on how to adapt the test procedures for these glass products are offered in Clause 4. All the considerations of this standard relate to panes of glass/glass products alone. Incorporation of them into windows may cause changes in acoustic performance as a result of other influences, e.g. frame design, frame material, glazing material/method, mounting method, air tightness, etc. Measurements of the sound insulation of complete windows (glass and frame) may be undertaken to resolve such issues.

Refrigerating systems and heat pumps - Competence of personnel

Document Number: NL EN 13771 1 : 2019

This European Standard defines the activities related to refrigerating circuits and the associated competenceprofiles and establishes procedures for assessing the competence of persons who carry out these activities. NOTE As a refrigerating circuit is considered not to incorporate electrical and electronic systems, activities in this area are not part of this standard. For competences on electrical and electronic systems, it is recommended to refer to national regulations or appropriate European or national standards. This European Standard does not apply to persons carrying out work on self contained refrigerating systems as defined in EN 378-1 from the initial design of the product to the complete manufacture of the product, provided the process is controlled and the methods used are checked by an organisation or individual, responsible for the compliance with statutory requirements on health, safety and environment.

NULL

Sector: NULL

Document Number: NL ISO 11660 1 : 2019

NULL

Cranes -- Access, guards and restraints -- Part 1: General

Document Number: NL ISO 11660 2 : 2019

This part of ISO 11660 establishes the general requirements for access to control stations and other areas of cranes as defined in ISO 4306-1, during normal operations, maintenance, inspection, erection, dismantling and emergency. It also deals with guards and restraints in general, concerning the protection of persons on or near the crane with regard to moving parts, falling objects or live parts. The particular requirements relating to access, guards and restraints for the various types of cranes and lifting appliances are given in ISO 11660-2, ISO 11660-3 and ISO 11660-5. In some cases, the particular requirements may not comply with the general requirements. Different dimensions can be permitted provided an equivalent degree of protection is achieved.

Cranes -- Access, guards and restraints -- Part 2: Mobile cranes

Document Number: NL ISO 11660 3 : 2019

This part of ISO 11660 establishes the particular requirements relating to access, guards and restraints for mobile cranes as defined in ISO 4306-1. ISO 11660-1 establishes the general requirements for access to control stations and other areas of cranes as defined in ISO 4306-1, during normal operations, maintenance, inspection, erection and dismantling. It also deals with guards and restraints in general, concerning the protection of persons on or near the crane with regard to moving parts, falling objects or live parts.

Cranes -- Access, guards and restraints -- Part 3: Tower cranes

Sector: Materials Handling Equipment

Document Number: NL EN 1176 11 : 2019

This part of ISO 11660 establishes the particular requirements relating to access, guards and restraints for tower cranes as defined in ISO 4306-3. ISO 11660-1 establishes the general requirements for access to control stations and other areas of cranes as defined in ISO 4306-1, during normal operations, maintenance, inspection, erection and dismantling. It also deals with guards and restraints in general, concerning the protection of persons on or near the crane with regard to moving parts, falling objects or live parts.

Playground equipment and surfacing - Part 11: Additional specific safety requirements and test methods for spatial network

Sector: Domestic and commercial Equipment. Entertainment.S

Document Number: NL EN 16051 2 : 2019

This European Standard specifies additional safety requirements for spatial networks intended for permanent installation for use by children. This European Standard is not applicable to artificial climbing structures, which are used for training for sports activities, e.g. alpinism.

Inflation devices and accessories for inflatable consumer products - Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators

Sector: FLUID SYSTEMS AND COMPONENTS FOR GENERAL USE

Document Number: NL EN 1729 2 : 2019

This document specifies the interface geometry between valves and pump adapters as well as flow rate performance, pressure, marking and labelling for air pumps for inflatable consumer articles (see definition in 3.1). This document does not apply to: - valves of personal flotation devices according to EN ISO 12402; - diving accessories and buoyancy compensators according to EN 1809. This document excludes the following valve types: - valves used for bicycles and vehicles; - needle valves (e. g. valves used for team sport balls).

Furniture - Chairs and tables for educational institutions - Part 2: Safety requirements and test methods

Sector: Domestic and commercial Equipment. Entertainment.S

Document Number: NL EN 1957 : 2019

This European Standard specifies safety requirements and test methods for chairs and tables for general educational purposes in educational institutions. It applies to furniture for use with laptop computers or portable devices, but not to special purpose workstations, e.g. laboratories, ranked seating and workshops. Annex A (normative) includes a test method for the drop test of chairs. With the exception of Annex A, the figures illustrate test principles only and cannot be used to carry out the tests. NOTE EN 1729 1 specifies functional dimensions and marking of chairs and tables for general educational purposes.

Furniture - Beds and mattresses - Test methods for the determination of functional characteristics and assessment criteria

Sector: Domestic and commercial Equipment. Entertainment.S

Document Number: NL EN 1730 : 2019

This European standard specifies test methods for the determination of the durability and hardness of mattresses and all types of fully erected beds with mattresses (and mattress pads when they form a unit with the mattress). It does not apply to water beds, air beds and children cots. It includes a method for the determination of the firmness rating of a mattress or a bed correlating to the subjective assessment made by people (see Annex A). It must be emphasized that the firmness rating cannot be used to demonstrate comfort and/or quality of a mattress or a complete bed. Ageing and degradation caused by air, light, humidity and temperature is not included. The test results are only valid for the article tested. When test results are intended to be applied to other similar articles, the test specimen shall be representative of them.

Furniture - Tables - Test methods for the determination of stability, strength and durability

Sector: Domestic and commercial Equipment. Entertainment.S

Document Number: NL ISO 20795 1 : 2019

This European Standard specifies test methods for the determination of stability, strength and durability of the structure of all types of tables and desks without regard to use, materials, design/construction or manufacturing process. This European Standard does not apply to changing units which are covered by other European Standards. Test methods for the assessment of ageing, degradation, and electrical functions are not included. This European Standard does not apply to the strength and durability of any storage features that are covered by other European Standards. This European Standard does not include any requirements. Requirements for different end uses can be found in other Standards.

Dentistry — Base polymers — Part 1: Denture base polymers

Document Number: NL ISO 20795 2 : 2019

ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements. It further specifies requirements with respect to packaging and marking the products and to the instructions to be supplied for use of these materials. Furthermore, it applies to denture base polymers for which the manufacturer claims that the material has improved impact resistance. It also specifies the respective requirement and the test method to be used. ISO 20795-1:2013 applies to denture base polymers such as those listed below: poly(acrylic acid esters); poly(substituted acrylic acid esters); poly(vinyl esters); polystyrene; rubber modified poly(methacrylic acid esters); polycarbonates; polysulfones; poly(dimethacrylic acid esters); polyacetals (polyoxymethylene); copolymers or mixtures of the polymers listed in 1 to 9.

Dentistry — Base polymers — Part 2: Orthodontic base polymers

Document Number: NL ISO 21563 : 2019

ISO 20795-2:2013 is applicable to orthodontic base polymers and copolymers used in the construction of both active and passive orthodontic appliances and specifies their requirements. It also specifies test methods to be used in determining compliance with these requirements. It further specifies requirements with respect to packaging and marking the products and to the instructions to be supplied for use of these materials.

Dentistry — Hydrocolloid impression materials

Document Number: NL ISO 22112 : 2019

Price: 50000.0000

ISO 21563:2013 specifies the requirements and tests for helping determine whether the elastic aqueous agar and alginate hydrocolloid dental impression materials, as prepared for retail marketing, are of the quality needed for their intended purposes. It also specifies requirements for labelling and instructions for use.

Dentistry — Artificial teeth for dental prostheses

Document Number: NL ISO 22674 : 2019

ISO 22112:2017 specifies the classification, requirements, and test methods for artificial teeth such as ceramic teeth and polymer teeth that are industrially manufactured for use in dental prostheses.

Dentistry — Metallic materials for fixed and removable restorations and appliances

Document Number: NL ISO 28319 : 2019

Price: 50000.0000

ISO 22674:2016 classifies metallic materials that are suitable for the fabrication of dental restorations and appliances, including metallic materials recommended for use either with or without a ceramic veneer, or recommended for both uses, and specifies their requirements. Furthermore, it specifies requirements with respect to packaging and marking the products and to the instructions to be supplied for the use of these materials, including products delivered for sale to a third party. ISO 22674:2016 does not apply to alloys for dental amalgam (ISO 24234), dental brazing materials (ISO 9333), or metallic materials for orthodontic appliances (ISO 15841) (e.g. wires, brackets, bands and screws).

Dentistry — Laser welding and filler materials

Document Number: NL ISO 17088 : 2019

ISO 28319:2018 specifies requirements and test methods for laser welding and the filler materials thereto used in the dental laboratory for welding of metallic restorations and appliances. For filler materials used in laser welding, this document also specifies the information given in the instructions for use, marking and labelling.

Specifications for compostable plastics

Sector: Rubber and Plastics Industries

Document Number: NL ISO 17422 : 2019

This International Standard specifies procedures and requirements for the identification and labelling of plastics, and products made from plastics, that are suitable for recovery through aerobic composting. The four following aspects are addressed: a) biodegradation; b) disintegration during composting; c) negative effects on the composting process and facility; d) negative effects on the quality of the resulting compost, including the presence of high levels of regulated metals and other harmful components. This specification is intended to establish the requirements for the labelling of plastic products and materials, including packaging made from plastics, as “compostable” or “compostable in municipal and industrial composting facilities” or “biodegradable during composting” (for the purposes of this International Standard, these three expressions are considered to be equivalent). The labelling will, in addition, have to conform to all international, regional, national or local regulations (e.g. European Directive 94/62/EC). NOTE The recovery of compostable plastics through composting can be carried out under the conditions found in well-managed composting plants, where the temperature, water content, aerobic conditions, carbon/nitrogen ratio and processing conditions are optimized. Such conditions are generally obtained in industrial and municipal composting plants. Under these conditions, compostable plastics will disintegrate and biodegrade at rates comparable to yard trimmings, kraft paper bags and food scraps.

Plastics — Environmental aspects — General guidelines for their inclusion in standards

Sector: Rubber and Plastics Industries

Document Number: NL ISO 15985 : 2019

This document provides a structure for inclusion of environmental aspects in standards for plastics products. It proposes an approach which is directed at minimizing any adverse environmental impact without detracting from the primary purpose of ensuring adequate fitness for use of the products under consideration. The guidance provided by this document is intended primarily for use by standards writers. Over and above its primary purpose, however, this document provides guidance of value to those involved in design work and other activities where environmental aspects of plastics are being considered. NOTE This document is intended to promote the following practices: a) the use of techniques for identifying and assessing the environmental impact of technical provisions in standards, and for minimizing their adverse effects; b) the adoption of good practices such as: 1) procedures for pollution avoidance, e.g. through end-of-life options and its proper management; 2) material and energy conservation in the light of the intended use (and foreseeable misuse) of the product; 3) safe use of hazardous substances; 4) avoidance of technically unjustifiable restrictive practices; 5) promotion of performance criteria rather than exclusion clauses such as are based, for example, only on chemical composition criteria; 6) use of renewable resources and minimization of the use of non-renewable resources, if the life cycle assessment shows favourable; c) the adoption of a balanced approach in standards development to issues such as environmental impact, product function and performance, health and safety, and other regulatory requirements; d) the regular review and revision of existing standards in the light of technical innovations, permitting improvement in the environmental impact of products and processes; e) the application of life cycle analytical approaches wherever applicable and technically justifiable.

Plastics — Determination of the ultimate anaerobic biodegradation under high-solids anaerobic-digestion conditions — Method by analysis of released biogas

Sector: Rubber and plastic industries

Document Number: NL ISO 16929 : 2019

ISO 15985 specifies a method for the evaluation of the ultimate anaerobic biodegradability of plastics based on organic compounds under high-solids anaerobic-digestion conditions by measurement of evolved biogas at the end of the test. This method is designed to simulate typical anaerobic digestion conditions for the organic fraction of mixed municipal solid waste. The test material is exposed in a laboratory test to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste. The anaerobic decomposition takes place under high-solids (more than 20 % total solids) and static non-mixed conditions. The test method is designed to yield the percentage of carbon in the test material and its rate of conversion to evolved carbon dioxide and methane (biogas).

Plastics — Determination of the degree of disintegration of plastic materials under defined composting conditions in a pilot-scale test

Sector: Rubber and plastic industries

Document Number: NL ISO 20200 : 2019

This International Standard is used to determine the degree of disintegration of plastic materials in a pilot-scale aerobic composting test under defined conditions. It forms part of an overall scheme for the evaluation of the compostability of plastics as outlined in ISO 17088. The test method laid down in this International Standard can also be used to determine the influence of the test material on the composting process and the quality of the compost obtained. It cannot be used to determine the aerobic biodegradability of a test material. Other methods are available for this (e.g. see ISO 14851, ISO 14852 or ISO 14855-1 and ISO 14855-2.

Plastics — Determination of the degree of disintegration of plastic materials under simulated composting conditions in a laboratory-scale test

Sector: Rubber and plastic industries

Document Number: NL ISO 9927 1 : 2019

ISO 20200specifies a method of determining the degree of disintegration of plastic materials when exposed to a laboratory-scale composting environment. The method is not applicable to the determination of the biodegradability of plastic materials under composting conditions. Further testing is necessary to be able to claim compostability.

Cranes — Inspections —Part 1:General

Document Number: NL ISO 9927 3 : 2019

ISO 9927 specifies the general requirements for inspections to be carried out on cranes as defined in ISO 4306‑1. Additional requirements for particular types of cranes are intended to be covered by the relevant specific parts of ISO 9927.

Cranes — Inspections —Part 3:Tower cranes

Document Number: NL ISO 9374 1 : 2019

This part of ISO 9927 specifies the regular inspections to be carried out on tower cranes. It is intended to be used in conjunction with ISO 9927-1. It does not cover inspection prior to the first use of a tower crane.

Cranes -- Information to be provided -- Part 1: General

Document Number: NL ISO 9374 3 : 2019

This standard Specifies generally the information to be provided by the purchaser and the manufacturer so that the most suitable crane can be supplied for the duty requirements and service conditions. Refers to ISO 4301-1 und ISO 7363.

Cranes -- Information to be provided for enquiries, orders, offers and supply -- Part 3: Tower cranes

Document Number: NL ISO 9374 4 : 2019

ISO 9374-3 gives guidance for information to be provided: a) by the purchaser when enquiring for a tower crane, b) by the purchaser when ordering a tower crane, c) by a manufacturer when offering (tendering) for a tower crane, d) by the manufacturer when supplying a tower crane.

Cranes -- Information to be provided -- Part 4: Jib cranes

Document Number: NL ISO 9100 9 : 2019

This standard Specifies information to be provided by a purchaser in enquiring for or ordering a jib crane and by a manufacturer in tendering for or supplying this crane. Annex A gives a format for information to be provided by the purchaser.

Glass Containers — Vacuum Lug Finishes — Part 9: 63, 66 and 70 Deep

Sector: Packaging and Distribution of Goods

Document Number: NL ISO 9100 10 : 2019

This document specifies the dimensions of vacuum lug finishes with nominal sizes of 63, 66 and 70 mm deep for wide-mouth glass containers.

Glass Containers — Vacuum Lug Finishes — Part 10: 77 Regular

Sector: Packaging and Distribution of Goods

Document Number: NL 241 : 2019

This document specifies the dimensions of a vacuum lug finish with a nominal size of 77 mm regular for widemouth glass containers.

Pickled fruits and vegetables

Sector: Food Technology

Document Number: NL EN 14073 2 : 2019

تسري هذه المواصفة على المنتجات المعرف عنها في القسم 2 والمعروضة للاستهلاك المباشر، بما في ذلك لأغراض التموين أو لإعادة التعبئة اذا دعت الحاجة. وتشمل هذه المواصفة على سبيل المثال لا لاحصر المنتجات التالية: البصل، الثوم، المانجو، الفجل، الزنجبيل، الشمندر، الخوخ الملكي، الفلفل، قلب النخيل، الملفوف، الخس، الليمون، الذرة الصغيرة (اليافعة) والخردل الأخضر.. وهي لا تسري على المنتج اذا كان سيخضع لمزيد من التجهيز ولا تشمل هذه المواصفة كذلك الكمتشي وزيتون المائدة والساور كروات وصلصة شاتني والمقبلات.

Office furniture - Storage furniture - Part 2: Safety requirements

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL EN 527 1 : 2019

This document specifies safety requirements for office storage furniture. This document does not apply to high density mechanized filing systems, rotary filing systems or plan files. It should be understood that fulfilling the specified requirements does not ensure that failure will not occur as a result of habitual misuse or after an excessively long period of service. Safety depending on structure of the building is not included e.g.: the strength of wall hanging cabinets includes only the cabinet and its parts. The wall and wall attachment are not included. Assessment of ageing is not included.

Office furniture - Work tables and desks - Part 1: Dimensions

Sector: Domestic and Commercial Equipment. Entertainment.

Document Number: NL ISO 14021 : 2018

This European Standard specifies dimensions of work tables and desks for office tasks to be undertaken in a seated, a sit stand or standing position. It includes neither dimensions for storage unit nor those for other tables in the office area or reception desks.

Environmental labels and declarations -- Self-declared environmental claims (Type II environmental labelling)

Sector: Construction materials and building

Document Number: NL EN 81 22 : 2018

This International Standard specifies requirements for self-declared environmental claims, including statements, symbols and graphics, regarding products. It further describes selected terms commonly used in environmental claims and gives qualifications for their use. This International Standard also describes a general evaluation and verification methodology for self-declared environmental claims and specific evaluation and verification methods for the selected claims in this International Standard. This International Standard does not preclude, override, or in any way change, legal

Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path

Document Number: NL EN 81 41 AMD 1 : 2018

Price: 50000.0000

1.1 This European Standard specifies the safety rules for the construction and installation of permanently installed new electric lifts, with traction or positive drive, serving defined landings levels, having a vehicle designed to convey passengers or passengers and loads, suspended by ropes or chains and travelling in a vertical plan along guide rails that are inclined at an angle of between 15° and 75° in relation to the horizontal. 1.2 In addition to the requirements of this standard, supplementary requirements should be considered in special cases (potentially explosive atmosphere, extreme climate conditions, seismic conditions, transporting dangerous goods, etc.). 1.3 This European Standard does not cover: a) lifts with drives other than those stated in 1.1; b) installation of electric lifts in existing buildings to the extent that space does not permit; c) important modifications (see Annex E) to a lift installed before this standard is brought into application; d) lifting appliances, such as paternosters, mine lifts, theatrical lifts, appliances with automatic caging, skips, lifts and hoists for building and public works sites, ships' hoists, platforms for exploration or drilling at sea, construction and maintenance appliances; e) safety during transport, installation, repairs, and dismantling of lifts; f) lifts with rated speed ≤ 0,15 m/s. However, this standard may usefully be taken as a basis. Noise is not dealt with in this standard because it is not relevant to the safe use of the lift. Vibrations are dealt with for electric parts only. Direct effects on human bodies are not considered as harmful. 1.4 This European Standard does not specify the additional requirements necessary for the use of lifts in case of fire. 1.5 Taking into account the state of art, the scope of the present standard is limited as follows: — inclination: a variation in inclination is permitted for the travel path; — travel path: confined within the vertical plane; — maximum capacity of the car: 7 500 kg (100 passengers); — maximum rated speed (v): 4 m/s. Both characteristics (capacity and speed) are linked by the relation given in the following Figure 1.

Safety Rules For The Construction And Installation Of Lifts – Special Lifts For The Transport Of Persons And Goods - Part 41: Vertical Lifting Platforms Intended For Use By Persons With Impaired Mobility

Document Number: NL EN 81 40 : 2018

1.1 This European Standard deals with safety requirements for construction, manufacturing, installation, maintenance and dismantling of electrically operated stairlifts (chair, standing platform and wheelchair platform) affixed to a building structure, moving in an inclined plane and intended for use by persons with impaired mobility:  travelling over a stair or an accessible inclined surface;  intended for use by one person;  whose carriage is directly retained and guided by a guide rail or rails;  supported or sustained by rope (5.4.4), rack and pinion (5.4.5), chain (5.4.6), screw and nut (5.4.7), friction traction drive (5.4.8), and guided rope and ball (5.4.9). 1.2 The standard identifies hazards as listed in Clause 4 which arise during the various phases in the life of such equipment and describes methods for the elimination or reduction of these hazards when used as intended by the manufacturer. 1.3 This European standard does not specify the additional requirements for:  operation in severe conditions (e.g. extreme climates, strong magnetic fields);  lightning protection;  operation subject to special rules (e.g. potentially explosive atmospheres);  handling of materials the nature of which could lead to dangerous situations;  use of energy systems other than electricity;  hazards occurring during manufacture;  earthquakes, flooding, fire;  type C wheelchairs as defined in EN 12183 and/or EN 12184;  evacuation during a fire;  stairlifts for goods only;  concrete, hardcore, timber or other foundation or building arrangement;  design of anchorage bolts to the supporting structure. NOTE For the actual type of machinery, noise is not considered a significant nor relevant hazard. 1.4 This document is not applicable to power operated stairlifts which are manufactured before the date of publication of this document by CEN.

Safety Rules For The Construction And Installation Of Lifts –Special Lifts For The Transport Of Persons And Goods - Part 40: Stairlifts And Inclined Lifting Platforms Intended For Persons With Impaired Mobility

Document Number: NL EN 81 21 AMD 1 : 2018

Safety Rules For The Construction And Installation Of Lifts - Lifts For The Transport Of Persons And Goods - Part 21: New Passenger And Goods Passenger Lifts In Existing Buildings

Document Number: NL EN 81 70 AMD 1 : 2018

This European Standard specifies the safety rules related to new passenger and goods/passenger lifts permanently installed in existing buildings where in some circumstances due to limitations enforced by building constraints, some requirements of EN 81-1 and EN 81-2 cannot be met (see also 4th sentence of Introduction). This European Standard addresses a number of these constraints and gives requirements for alternative solutions. It shall be read and applied in conjunction with the European Standards EN 81-1 or EN 81-2 !deleted text", including their Clause 0. This European Standard covers:  Either the construction and installation of one or more complete new lift(s) including new well and machinery spaces in an existing building; or  The replacement of one or more existing lift(s) by new ones in existing well(s) and machinery spaces. This European Standard does not cover:  Replacement or modifications of some parts to a lift already installed;  Other applications outside of the scope of EN 81-1 or EN 81-2.

Safety rules for the construction and installations of lifts-Particular applications for passenger and good passengers lifts -Part 70: Accessibility to lifts for persons including persons with disability

Document Number: NL EN 81 82 AMD 1 : 2018

This European Standard specifies the minimum requirements for the safe and independent access and use of lifts by persons, including persons with the disabilities mentioned in annex B, Table B.1. This European Standard covers lifts with minimum car dimensions according to Table 1 and provided with car doors and landing doors constructed as automatic power operated horizontally sliding doors. This European Standard considers accessibility to lifts for persons using wheelchairs with maximum overall dimensions defined in EN 12183:1999 and EN 12184:1999. This European Standard also deals with the additional technical requirements to minimise the hazards listed in clause 4 that arise during the operation of lifts intended to be accessible to disabled users. NOTE This standard can be used as guidance for upgrading existing lifts in line with the recommendation of the European Commission dated 8th of June, 1995 (95/216/EC) concerning improvements to safety of existing lifts.

Safety rules for the construction and installation of lifts - Existing lifts - Part 82: Rules for the improvement of the accessibility of existing lifts for persons including persons with disability

Document Number: NL 137 : 2018

1.1 This European Standard provides rules on how to apply EN 81-70 referred to in EN 81-80:2003, 5.2.1 [4] to existing lifts to improve their accessibility for persons including persons with disability. 1.2 This European Standard applies to permanently installed lifts serving defined landing levels, having a car designed for the transportation of persons or persons and goods and moving between guide rails inclined not more than 15° to the vertical.

Wind Action on Buildings

Document Number: NL 604 : 2018

(1) The present Standard gives rules and methods of calculation for loads of wind exercised on buildings of height lower than 200 ms, their components and their appendixes. (2) Loads of wind must be calculated for each of zones affected by these actions: - the whole of the structure; - or a part of the structure, that is some of his/her/its elements, shifting boards and their fixings. (3) The present Standard also gives rules for chimneys and other recessed structures in foot. The relative special conditions to towers in lattice don't appear there.

Foods for special dietary use for persons intolerant to gluten

Sector: Food Technology