Document Number:
NL ISO 15995 : 2008
Sector:
Fluid systems and components for general use
Status:
C
Production Year:
2008
Price:
35000.0000
This International Standard specifies the requirements for design, specification and type testing of dedicated LPG manually operated cylinder valves specifically for use with transportable refillable LPG cylinders from 0,5 l up to 150 l water capacity. It includes references to associated equipment for vapour or liquid service. NOTE Annex C gives the recommendations for production testing and inspection. This International Standard does not apply to fixed automotive installations.
Document Number:
NL ISO 16949 : 2008
Sector:
Sociology. Services. Company Organization and Mana
Status:
C
Production Year:
2008
Price:
50000.0000
1.1 General ISO 9001:2000, Quality management systems — Requirements 1 Scope 1.1 General This International Standard specifies requirements for a quality management system where an organization. a) needs to demonstrate its ability to consistently provide product that meets customer and applicable regulatory requirements, and b) aims to enhance customer satisfaction through the effective application of the system, including processes for continual improvement of the system and the assurance of conformity to customer and applicable regulatory requirements. NOTE In this International Standard, the term “product” applies only to the product intended for, or required by, a customer. This Technical Specification, in conjunction with ISO 9001:2000, defines the quality management system requirements for the design and development, production and, when relevant, installation and service of automotive-related products. This Technical Specification is applicable to sites of the organization where customer-specified parts, for production and/or service, are manufactured. Supporting functions, whether on-site or remote (such as design centres, corporate headquarters and distribution centres), form part of the site audit as they support the site, but cannot obtain stand-alone certification to this Technical Specification. This Technical Specification can be applied throughout the automotive supply chain. 1.2 Application ISO 9001:2000, Quality management systems — Requirements 1.2 Application All requirements of this International Standard are generic and are intended to be applicable to all organizations, regardless of type, size and product provided. Where any requirement(s) of this International Standard cannot be applied due to the nature of an organization and its product, this can be considered for exclusion. Where exclusions are made, claims of conformity to this International Standard are not acceptable unless these exclusions are limited to requirements within clause 7, and such exclusions do not affect the organization's ability, or responsibility, to provide product that meets customer and applicable regulatory requirements. The only permitted exclusions for this Technical Specification relate to 7.3 where the organization is not responsible for product design and development. Permitted exclusions do not include manufacturing process design
Document Number:
NL ISO 17664 : 2008
Sector:
Health Care Technology
Status:
C
Production Year:
2008
Price:
35000.0000
This document specifies requirements for the information to be provided by the medical device manufacturer for the processing of a medical device that requires cleaning followed by disinfection and/or sterilization to ensure that the device is safe and effective for its intended use. This includes information for processing prior to use or reuse of the medical device. The provisions of this document are applicable to medical devices that are intended for invasive or other direct or indirect patient contact. Processing instructions are not defined in this document. Rather, this document specifies requirements to assist manufacturers of medical devices in providing detailed processing instructions that consist of the following activities, where applicable: a) initial treatment at the point of use; b) preparation before cleaning; c) cleaning; d) disinfection; e) drying; f) inspection and maintenance; g) packaging; h) sterilization; i) storage; j) transportation. This document excludes processing of the following: *non-critical medical devices not intended for direct patient contact; *textile devices used in patient draping systems or surgical clothing; *medical devices specified by the manufacturer for single-use only and supplied ready for use.
Document Number:
NL ISO 18777 : 2008
Sector:
Health Care Technology
Status:
C
Production Year:
2008
Price:
35000.0000
IEC 60601-1:1988, Clause 1, applies except as follows: Amendments (add at end of 1.1): 1.1This International Standard specifies requirements for the safety and essential performance of transportable liquid oxygen systems which are used as a supply source for oxygen therapy. These devices usually consist of a portable unit to be carried by or with the patient whilst in use and the vessel used to refill the portable unit. These devices are mostly used in home care applications and in health care facilities/institutions. These devices are often used without professional supervision. Liquid oxygen vessels used as a supply source for oxygen pipeline systems are excluded from this International Standard. The requirements of this International Standard which replace or modify the requirements of IEC 60601-1:1998 and its Amendments 1 (1991) and 2 (1995) are intended to take precedence over the corresponding general requirements. 1.4 Addition: NOTE Planning and design of products complying with this Internatinal Standard can have environmental impact during the product life cycle. Environmental aspects are addressed in Annex BB. Additional aspects of environmental impact are addressed in ISO 14971.
Document Number:
NL ISO 18779 : 2008
Sector:
Health Care Technology
Status:
C
Production Year:
2008
Price:
35000.0000
This International Standard specifies requirements for the safety and essential performance of portable devices that supply the flow of oxygen or oxygen mixtures during therapy (e.g. long term oxygen therapy,analgesia). These devices1) are intended to conserve oxygen or oxygen mixtures by delivering these gases intermittently on the patient's demand when used in home care applications. These devices are generally used without continual professional supervision. These devices are also used in health care facilities/institutions. This International Standard covers two types of conserving devices (see 3.5 and 3.6): conserving devices intended for continuous use and those not intended for continuous use. This International Standard covers active devices only, e.g. pneumatically or electrically controlled devices,and does not cover devices such as reservoir cannulas. This International Standard also includes conserving devices which are part of a system, e.g. pressure regulators, oxygen concentrators or liquid oxygen vessels. The requirements of this International Standard which replace or modify the requirements of IEC 60601-1:1988 and its Amendments 1 (1991) and 2 (1995) are intended to take precedence over the corresponding general requirements. 1.4 Addition: NOTE Planning and design of products complying with this International Standard can have environmental impactduring the product life cycle. Environmental aspects are addressed in Annex BB. Additional aspects of environmental impact are addressed in ISO 14971.
Document Number:
NL ISO 19011 : 2008
Sector:
Sociology. Services. Company Organization and Mana
Status:
C
Production Year:
2008
Price:
35000.0000
This document provides guidance on auditing management systems, including the principles of auditing, managing an audit programme and conducting management system audits, as well as guidance on the evaluation of competence of individuals involved in the audit process. These activities include the individual(s) managing the audit programme, auditors and audit teams. It is applicable to all organizations that need to plan and conduct internal or external audits of management systems or manage an audit programme. The application of this document to other types of audits is possible, provided that special consideration is given to the specific competence needed.
Document Number:
NL ISO 15213 : 2008
Sector:
Food Technology
Status:
C
Production Year:
2008
Price:
25000.0000
This International Standard specifies a horizontal method for the enumeration of sulfite-reducing bacteria growing under anaerobic conditions. It is applicable to : — products intended for human consumption and the feeding of animals, and — environmental samples in the area of food production and food handling.
Document Number:
NL ISO 14937 : 2008
Sector:
Health Care Technology
Status:
C
Production Year:
2008
Price:
50000.0000
1.1.1 This International Standard specifies general requirements for the characterization of a sterilizing agent and for the development, validation and routine monitoring and control of a sterilization process for medical devices. NOTE Although the scope of this International Standard is limited to medical devices, the requirements specified herein can also be applied to sterilization processes for other health care products. 1.1.2 This International Standard applies to sterilization processes in which microorganisms are inactivated by physical and/or chemical means. 1.1.3 This International Standard is intended to be applied by process developers, manufacturers of sterilization equipment, manufacturers of medical devices to be sterilized, and organizations responsible for sterilizing medical devices. 1.1.4Tthis International Standard specifies the elements of a Quality Management System which are necessary to assure the appropriate characterization of the sterilizing agent, development, validation and routine monitoring and control of a sterilization process. NOTE It is not a requirement of this International Standard to have a full quality management system. The necessary elements are normatively referenced at appropriate places in the text (see, in particular, Clause 4). Attention is drawn to the standards for quality management systems (see ISO 13485) that control all stages of production or reprocessing of medical devices. National and/or regional regulations for the provision of medical devices might require the implementation of a full quality management system and the assessment of that system by a third party"
Document Number:
NL EN ISO 14971 : 2008
Sector:
Health Care Technology
Status:
C
Production Year:
2008
Price:
50000.0000
This International Standard specifies a process for a manufacturer to identify the hazards associated with medical devices, including in vitro diagnostic (IVD) medical devices, to estimate and evaluate the associated risks, to control these risks, and to monitor the effectiveness of the controls. The requirements of this International Standard are applicable to all stages of the life-cycle of a medical device. This International Standard does not apply to clinical decision making. This International Standard does not specify acceptable risk levels. This International Standard does not require that the manufacturer have a quality management system in place. However, risk management can be an integral part of a quality management system.
Document Number:
NL EN 13954 : 2008
Sector:
Food Technology
Status:
C
Production Year:
2008
Price:
50000.0000
1.1 This European Standard specifies safety and hygiene requirements for the design and manufacture of bread slicing machines of type 1 and 2 as defined in Clause 3. The intended use of these machines is to cut baked bread into slices. This European Standard deals with all significant hazards, hazardous situations and events relevant to bread slicers machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard covers requirements for the safe operation of the machine including: loading, cutting,unloading, cleaning, crumb removal and maintenance. These machines can be manually or automatically operated. 1.2 The following machines are excluded from the scope of this document: experimental and testing machines under development by the manufacturer; frame cutter machines with multiple blades moving horizontally; domestic appliances and machines intended for use by the general public; machines with horizontal circular cutting systems; rectangular cutting machines for cutting or sawing of panel size products into small pieces. The significant hazards covered by this document are described in Clause 4. 1.3 In drafting this European Standard, it has been assumed that the bread slicers falling within the scope are operated only by trained personnel and that the machines are not intended to be cleaned with water jet. 1.4 This European Standard is not applicable to bread slicing machines which are manufactured before the date of publication of this European Standard.
Document Number:
NL IEC 60921 : 2008
Sector:
Electrical Engineering
Status:
C
Production Year:
2008
Price:
50000.0000
This standard specifies performance requirements for ballasts, excluding resistance types, for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with tubular fluorescent lamps with pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in IEC 60081 and 60901. It applies to complete ballasts and their component parts such as resistors, transformers and capacitors. This consolidated version consists of the second edition (2004) and its amendment 1 (2006). Therefore, no need to order amendment in addition to this publication
Document Number:
NL IEC 60927 : 2008
Sector:
Electrical Engineering
Status:
C
Production Year:
2008
Price:
50000.0000
IEC 60927:2007+A1:2013 specifies performance requirements for starting devices (starters and ignitors) for tubular fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, which produce starting pulses not greater than 5 kV. This consolidated version consists of the third edition (2007) and its amendment 1 (2013). Therefore, no need to order amendment in addition to this publication. This publication is to be read in conjunction with IEC 61347-1:2007 and IEC 61347-2-1:2000
Document Number:
NL IEC 60598 1 : 2008
Sector:
Electrical Engineering
Status:
C
Production Year:
2008
Price:
50000.0000
This Part 1 of IEC 60598 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V. The requirements and related tests of this standard cover: classification, marking, mechanical construction, electrical construction and photobiological safety. Each section of this Part 1 is read in conjunction with this Section 0 and with other relevant sections to which reference is made. Each part of IEC 60598-2 details requirements for a particular type of luminaire or group of luminaires on supply voltages not exceeding 1 000 V. These parts are published separately for ease of revision and additional sections will be added as and when a need for them is recognized. The presentation of photometric data for luminaires is under consideration by the International Commission on Illumination (CIE) and is not, therefore, included in this Part 1. Requirements are included in this Part 1 for luminaires incorporating ignitors with nominal peak values of the voltage pulse not exceeding those of Table 11.2. The requirements apply to luminaires with ignitors built into ballasts and to luminaires with ignitors separate from ballasts. For luminaires with ignitors built into lamps, the requirements are under consideration. Requirements for semi-luminaires are included in this Part 1. In general, this Part 1 covers safety requirements for luminaires. The object of this Part 1 is to provide a set of requirements and tests which are considered to be generally applicable to most types of luminaires and which can be called up as required by the detail specifications of IEC 60598-2. This Part 1 is thus not regarded as a specification in itself for any type of luminaire, and its provisions apply only to particular types of luminaires to the extent determined by the appropriate part of IEC 60598-2. The parts of IEC 60598-2, in making reference to any of the sections of Part 1, specify the extent to which that section is applicable and the order in which the tests are to be performed; they also include additional requirements as necessary. The order in which the sections of Part 1 are numbered has no particular significance as the order in which their provisions apply is determined for each type of luminaire or group of luminaires by the appropriate part of IEC 60598-2. All parts of IEC 60598-2 are self-contained and therefore do not contain references to other parts of IEC 60598-2. Where the requirements of any of the sections of Part 1 are referred to in the parts of IEC 60598-2 by the phrase "The requirements of section... of IEC 60598-1 apply", this phrase is to be interpreted as meaning that all the requirements of that section of Part 1 apply except those which are clearly inapplicable to the particular type of luminaire covered by that part of IEC 60598-2. This is a preview - click here to buy the full publication – 12 – IEC 60598-1:2014+AMD1:2017 CSV IEC 2017 For explosion proof luminaires, as covered by IEC 60079, the requirements of IEC 60598 (selecting the appropriate parts 2) are applied in addition to the requirements of IEC 60079. In the event of any conflict between IEC 60598 and IEC 60079, the requirements of IEC 60079 take priorit Improvements in safety to take into account the state of the art technology are incorporated in the standards with revisions and amendments on an ongoing basis. Regional standardisation bodies may include statements in their derived standards to cover products which have complied with the previous document as shown by the manufacturer or standardization body. The statements may require that for such products, the previous standard may continue to apply to production until a defined date after which the new standard shall appl
Document Number:
NL EN 14782 : 2008
Sector:
Construction Materials and Building
Status:
C
Production Year:
2008
Price:
35000.0000
This European Standard specifies the terminology, requirements and test methods for factory made self-supporting metal sheets and tiles (for non-structural applications) delivered in the form of manufactured pieces for roofing and wall cladding and lining. This standard also covers ceiling (including internal metal sheet) and soffit applications and cassettes (see Figure 1). This standard covers self-supporting copper, zinc, steel, aluminium and stainless steel sheet with or without coatings, e.g. metallic, organic, inorganic or multi-layer (see Annex A). A moisture retaining layer may be present on the reverse side of the product. This standard also includes rules for marking, labelling and evaluation of conformity. This standard does not cover products for structural purposes, i.e. it does not cover products intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to permanent static loads (excluding self-weight of the metal sheet). Requirements concerning acoustical and thermal insulation properties are not considered in this standard. This standard does not include calculation or design requirements with regards to the works, installation techniques or the performance of the installed products
Document Number:
NL EN 14783 : 2008
Sector:
Construction Materials and Building
Status:
C
Production Year:
2008
Price:
35000.0000
This European Standard specifies the terminology, requirements and test methods for metal coil, strip, and flat sheets and factory made pieces intended for fully supported applications in roofing and wall cladding or lining. It does not apply to products manufactured on site. This European Standard covers fully-supported aluminium, copper, lead, steel, stainless steel and zinc products with or without coatings, e.g. metallic, organic, inorganic or multi-layer (see Annex A). This European Standard also includes rules for marking, labelling and evaluation of conformity. Requirements concerning acoustical and insulation properties are not considered in this European Standard. This European Standard does not include calculation or design requirements with regards to the works, installation techniques or the performance of the installed products.
Document Number:
NL EN 13969 : 2008
Sector:
Construction Materials and Building
Status:
C
Production Year:
2008
Price:
35000.0000
This document specifies definitions and characteristics of flexible reinforced bitumen sheets for which the intended use is as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this standard.
Document Number:
NL EN 13970 : 2008
Sector:
Construction Materials and Building
Status:
C
Production Year:
2008
Price:
35000.0000
This document specifies definitions and characteristics of flexible reinforced bitumen sheets for which the intended use is as water vapour control layers for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.
Document Number:
NL ISO 14602 : 2008
Sector:
Health Care Technology
Status:
C
Production Year:
2008
Price:
25000.0000
This International Standard specifies particular requirements for non-active surgical implants for osteosynthesis, hereafter referred to as implants. In addition to ISO 14630, this International Standard gives particular requirements for intended performance, design attributes, materials, design evaluation, manufacturing, sterilization, packaging and information supplied by the manufacturer
Document Number:
NL ISO 14630 : 2008
Sector:
Health Care Technology
Status:
C
Production Year:
2008
Price:
25000.0000
This International Standard specifies general requirements for non-active surgical implants, hereafter referred to as implants. This International Standard is not applicable to dental implants, dental restorative materials, transendodontic and transradicular implants, intra-ocular lenses and implants utilizing viable animal tissue. With regard to safety, this International Standard specifies requirements for intended performance, design attributes, materials, design evaluation, manufacture, sterilization, packaging and information supplied by the manufacturer, and tests to demonstrate compliance with these requirements. Additional tests are given or referred to in level 2 and level 3 standards. NOTE This International Standard does not require that the manufacturer have a quality management system in place. However, the application of a quality management system, such as that described in ISO 13485, might be appropriate to help ensure that the implant achieves its intended performance.
Document Number:
NL EN 60335 2 24 : 2008
Sector:
Domestic and Commercial Equipment. Entertainment.
Status:
C
Production Year:
2008
Price:
50000.0000
This clause of Part 1 is replaced by the following. This International Standard deals with the safety of the following appliances, their rated voltage being not more than 250 V for single-phase appliances, 480 V for other appliances and 24 V d.c. for appliances when battery operated. – refrigerating appliances for household and similar use; – ice-makers incorporating a motor-compressor and ice-makers intended to be incorporated in frozen food storage compartments; – refrigerating appliances and ice-makers for use in camping, touring caravans and boats for leisure purposes. These appliances may be operated from the mains, from a separate battery or operated either from the mains or from a separate battery. This standard also deals with the safety of ice-cream appliances intended for household use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. It also deals with compression-type appliances for household and similar use, which use flammable refrigerants. This standard does not cover features of the construction and operation of those refrigerating appliances which are dealt with in ISO standards. Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account NOTE 1 Attention is drawn to the fact that – for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; NOTE 2 This standard does not apply to – appliances intended to be used in the open air; – appliances designed exclusively for industrial purposes; 7 egaP 3002:42−2−53306 NE Page 8 EN 60335−2−24:2003 # – persons (including children) whose – physical, sensory or mental capabilities; or – lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction; – children playing with the appliance.$ #– in many countries, additional requirements are specified by national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities. $ NL EN 60335-2-24:2008 – appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas); – appliances incorporating a battery intended as a power supply for the refrigerating function; – appliances assembled on site by the installer; – appliances with remote motor-compressors; – motor-compressors (IEC 60335-2-34); – commercial dispensing appliances and vending appliances (IEC 60335-2-75); – commercial ice-cream appliances.
Document Number:
NL IEC 60901 : 2008
Sector:
Electrical Engineering
Status:
C
Production Year:
2008
Price:
50000.0000
Specifies the performance requirements for single-capped fluorescent lamps for general lighting service. The requirements of this standard relate only to type testing. Conditions of compliance, including methods of statistical assessment, are under consideration. This consolidated version consists of the second edition (1996), its amendment 1 (1997) and its amendment 2 (2000). Therefore, no need to order amendments in addition to this publication
Document Number:
NL IEC 60155 : 2008
Sector:
Electrical Engineering
Status:
C
Production Year:
2008
Price:
50000.0000
La présente norme s'applique aux interrupteurs d'amorçage à lueur amovibles utilisés avec les lampes fluorescentes à cathodes préchauffées ci-après appelés «starters». La section 1 spécifie les prescriptions générales auxquelles les starters doivent être conformes. La section 2 spécifie des prescriptions de fonctionnement. NOTE — Les starters sont généralement conçus pour fonctionnement avec une gamme de lampes, selon la tension d'alimentation, le fonctionnement d'une seule lampe ou de lampes en série, la tension maximale de la lampe et les prescriptions d'amorçage de la lampe.
Document Number:
NL IEC 61199 : 2008
Sector:
Electrical Engineering
Status:
C
Production Year:
2008
Price:
50000.0000
IEC 61199:2011+A1:2012 specifies the safety requirements for single-capped fluorescent lamps for general lighting purposes of all groups having caps according to Table 1. It also specifies the method a manufacturer should use to show compliance with the requirements of this standard on the basis of whole production appraisal in association with his test records on finished products. This method can also be applied for certification purposes. Details of a batch test procedure which can be used to make limited assessment of batches are also given in this standard. This third edition cancels and replaces the second edition published in 1999. It constitutes a technical revision. Main technical changes are the introduction of requirements for high frequency operation, a new temperature measurement position and few new cap-holder fits. This consolidated version consists of the third edition (2011) and its amendment 1 (2012). Therefore, no need to order amendment in addition to this publication
Document Number:
NL EN 1919 : 2008
Sector:
Fluid systems and components for general use
Status:
C
Production Year:
2008
Price:
25000.0000
This standard: - specifies the inspection requirements at the time of filling and applies to seamless or welded transportable gas cylinders made of steel or aluminium alloy for liquefied gases (excluding acetylene and LPG) of water capacity from 0,5 litre up to 150 litres. It also applies, as far as practicable, to cylinders of less than 0,5 litre water capacity; - does not apply to manifolded bundles or manifolded trailer cylinders.
Document Number:
NL ISO 3500 : 2008
Sector:
Fluid systems and components for general use
Status:
C
Production Year:
2008
Price:
25000.0000
ISO 3500:2005 specifies the principal external dimensions, accessories, filling ratio, and marking for seamless steel CO2 cylinders used in fixed fire-fighting installations on cargo ships, passenger ships, salvage vessels, heavy-lift vessels, tug-barge combinations and offshore drilling and production platforms, any of which can be serviced in port or in dry dock, in order to facilitate the interchangeability of such cylinders.
Document Number:
NL ISO 5151 : 2008
Sector:
Fluid systems and components for general use
Status:
C
Production Year:
2008
Price:
50000.0000
This International Standard specifies the standard conditions on which the ratings of Single-package and Split-System non-ducted air conditioners employing air- and water-cooled condensers and heat Pumps employing air-cooled condensers are based, and the test methods to be applied for determination of the various ratings. This International Standard is limited to Systems utilizing a Single refrigeration circuit and having one evaporator and one condenser.
Document Number:
NL EN 1338 : 2007
Sector:
CIVIL ENGINEERING
Status:
C
Production Year:
2007
Price:
0
This European Standard specifies materials, properties, requirements and test methods for unreinforced cement bound concrete paving blocks and complementary fittings. It is applicable to precast concrete paving blocks and complementary fittings for pedestrian use, vehicular use and roof coverings, e.g. footpaths, precincts, cycle tracks, car parks, roads, highways, industrial areas (including docks and harbours), aircraft pavements, bus stations, petrol filling stations. In case of regular use of studded tyres additional requirements are sometimes needed. This standard does not deal with the tactility or visibility of blocks nor with permeable blocks. This standard provides for the product marking and the evaluation of conformity of the product to this European Standard.
Document Number:
NL EN 1339 : 2007
Sector:
CIVIL ENGINEERING
Status:
C
Production Year:
2007
Price:
50000.0000
This European Standard specifies materials, properties, requirements and test methods for cement bound unreinforced concrete paving flags and complementary fittings. It is applicable to precast concrete paving flags and complementary fittings that are for use in trafficked paved areas and roof coverings. In case of regular use of studded tyres additional requirements are sometimes needed. This standard does not deal with the tactility or visibility of flags nor with permeable flags. This standard provides for the product marking and the evaluation of conformity of the product to this European Standard.
Document Number:
NL EN 1344 : 2007
Sector:
CIVIL ENGINEERING
Status:
C
Production Year:
2007
Price:
50000.0000
This European Standard specifies the requirements of pavers and accessories manufactured from clay for use in the flexible form of construction (pavers laid with narrow sand-filled joints on a sand bed) and in the rigid form of construction (pavers laid with cementitious mortar joints on a similar mortar bed, itself placed on a rigid base). The standard applies to rectangular and other shaped units intended as construction products mainly for exterior use in pavements but which may also be used internally. The flexible form of construction will be subjected to pedestrian and vehicular traffic, while the rigid form of construction is usually subjected to pedestrian traffic. It excludes products intended for refractory and chemical engineering applications and clay floor tiles. It also excludes clay masonry units. This Standard does not deal with the tactility or visibility of units. This European Standard specifies the characteristics and classes of performance measured according to test methods given in normative annexes. It provides for product marking and for the evaluation of conformity of the product to this European Standard.
Document Number:
NL EN 13830 : 2007
Sector:
CIVIL ENGINEERING
Status:
C
Production Year:
2007
Price:
25000.0000
This European Standard specifies characteristics of curtain walling and provides technical information on the varying performance requirements which apply throughout Europe and the test criteria and sequence of testing to which the product is subjected, in order to demonstrate conformity. Reference is made to other European Standards related to the performance and testing of curtain walling and, where appropriate, attention is drawn to European Standards which relate to products incorporated into curtain walling. This standard applies to curtain walling ranging from a vertical position to 15° from the vertical, onto the building face. It can include elements of sloping glazing contained within the curtain wall. Curtain walling is not a product which can be completed in all respects within a manufacturing area, but is a series of components and/or prefabricated units which only become a finished product when assembled together on site. This standard is applicable to the whole of the cur
Document Number:
NL EN 1337 4 : 2007
Sector:
Construction Materials and Building
Status:
C
Production Year:
2007
Price:
35000.0000
This part of EN 1337 specifies the requirements for the design and manufacture of single and multiple roller bearings, in which the roller axis is horizontal. In order to accommodate displacements parallel to the roller axis roller bearings can be combined with sliding elements in accordance with EN 1337-2. To permit rotation about the axis perpendicular to the roller axis or about both axes, as for multiple roller bearings, the roller bearings can be combined with bearings from other parts of EN 1337. This part of EN 1337 does not apply to roller bearings made with materials other than those specified in clause 5. Bearings which are subjected to rotation greater than 0,05 rad resulting from the characteristic combination of actions are outside the scope of this part of EN 1337.
Document Number:
NL EN 1337 6 : 2007
Sector:
Construction Materials and Building
Status:
C
Production Year:
2007
Price:
25000.0000
This part of EN 1337 specifies the requirements for the design and manufacture of rocker bearings. In order to accommodate displacements rocker bearings can be combined with a sliding element in accordance with EN 1337-2. Bearings which are subjected to rotation greater than 0,05 rad resulting from the characteristic combination of actions are outside the scope of this part of EN 1337. This part of EN 1337 does not apply to rocker bearings made with materials other than those specified in clause 5.
Document Number:
NL IEC 61347 2 8 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
50000.0000
This part of IEC 61347 specifies safety requirements for ballasts, excluding resistance types, for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with fluorescent lamps with or without pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in IEC 60081 and 60901. This consolidated version consists of the first edition (2000) and its amendment 1 (2006). Therefore, no need to order amendment in addition to this publication. The contents of the corrigendum of August 2012 have been included in this copy.
Document Number:
NL EN ISO 14683 : 2007
Sector:
Construction Materials and Building
Status:
C
Production Year:
2007
Price:
50000.0000
ISO 14683:2007 deals with simplified methods for determining heat flows through linear thermal bridges which occur at junctions of building elements. ISO 14683:2007 specifies requirements relating to thermal bridge catalogues and manual calculation methods. Default values of linear thermal transmittance are given in Annex A for information
Document Number:
NL EN 40 7 : 2007
Sector:
Construction Materials and Building
Status:
C
Production Year:
2007
Price:
35000.0000
This part of this European Standard specifies the performance requirements for fibre reinforced polymer composite lighting columns for which the main intended use is road lighting. It includes materials and test methods. The composite materials considered are those constructed of a resin matrix reinforced by a high strength fibrous material. It applies to post top columns not exceeding 20 m height for post top lanterns and columns with brackets not exceeding 18 m height for side entry lanterns. This European Standard specifies the classes of performance related to the essential requirements of resistance to horizontal (wind) loads, and performance under vehicle impact (passive safety) in application of Essential Requirement No 4 Safety in Use measured according to the corresponding test methods included in this European Standard or available in separate European Standards. It provides for the evaluation of conformity of the product to this European Standard.
Document Number:
NL EN 13813 : 2007
Sector:
Construction Materials and Building
Status:
C
Production Year:
2007
Price:
35000.0000
This European Standard specifies requirements for screed material for use in floor construction internally. To support the aim of achieving a performance related standard, as far as practicable this standard refers only to the properties of the product and not to its method of manufacture, except when this is unavoidable in the description of the characteristics of the product. It defines for fresh screed material the performance related to setting time, consistency, pH value and for the hardened screed material, compressive strength, flexural strength, wear resistance, surface hardness, resistance to indentation, resistance to rolling wheel, shrinkage and swelling, modulus of elasticity, bond strength, impact resistance, reaction to fire, acoustic performance, thermal resistance and chemical resistance. It provides for the evaluation of conformity of the product to this European Standard. The marking requirements for products covered by this European Standard are included. This s
Document Number:
NL ISO 13850 : 2007
Sector:
Mechanical Systems and Components for General Use
Status:
C
Production Year:
2007
Price:
25000.0000
This International Standard specifies functional requirements and design principles for the emergency stop function on machinery, independent of the type of energy used. It does not deal with functions such as reversal or limitation of motion, deflection of emissions (e.g. radiation, fluids), shielding, braking or disconnecting, which can be part of the emergency stop function. The requirements for this International Standard apply to all machines, with exception to machines where an emergency stop would not reduce the risk hand-held or hand-operated machines. NOTE The requirements for the realization of the emergency stop function based on electrical/electronic technology are described in IEC 60204-1.
Document Number:
NL IEC 60598 2 9 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
35000.0000
This section of Part 2 of IEC Publication 598 specifies requirements for photo and film luminaires (non-professional) for use with tungsten filament lamps on supply voltages not exceeding 250 V, including low-pressure tungsten halogen lamps specified in IEC Publication 357 with the reference 357-IEC-3155. It is to be read in conjunction with those sections of Part 1 to which reference is made.
Document Number:
NL IEC 60598 2 10 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
25000.0000
This part of IEC 60598 specifies requirements for portable luminaires for children and for use with tungsten filament lamps or single capped fluorescent lamps on a supply voltage not exceeding 250 V. It is to be read in conjunction with those sections of Part 1 to which reference is made. This part is not applicable to the following: – portable luminaires typically placed as an extra ornamental element in temporary decorative configurations due to festivities or celebrations; – low illuminance background luminaires integral with a plug, i.e. forming part of a plug-in device; – battery driven luminaires or luminaires not for direct connection to the main supply; – toys; – luminaires designed or clearly intended for adult use; – luminaires with two-dimensional graphic reproductions of persons or animals (real or imaginary) on removable shades
Document Number:
NL IEC 60598 2 17 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
25000.0000
This part of IEC 60598-2 specifies requirements for stage, television, film and photographic studio luminaires (including spot and floodlighting projectors) for use outdoors and indoors, with electric light sources on supply voltages not exceeding 1 000 V. NOTE A hanger (stirrup) is a part of the luminaire. Supporting devices such as tripods, telescopic booms and suspensions are not parts of the luminaire. Where applicable, ballasts are built into or mounted separately from the luminaires.
Document Number:
NL IEC 60598 2 18 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
25000.0000
This section of Part 2 of IEC 598 specifies requirements for fixed luminaires intended for use in the water, or in contact with the water, in, for example, the basins of swimming pools, fountains, paddling pools, and garden pools, and for use with tungsten filament lamps. NOTE – Electrical installation rules for swimming pools are given in IEC 364-7-702: Electrical installations of buildings – Part 7: Requirements for special installations or locations – Section 702: Swimming pools. This section does not cover luminaires not in contact with the water (e.g. mounted behind a glass panel which is separate from the luminaire) or hand-held or portable luminaires. It is to be read in conjunction with those sections of Part 1 to which reference is made.
Document Number:
NL IEC 60598 2 1 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
25000.0000
This section of Part 2 of I E C Publication 598 specifies requirements for fixed general purpose luminaires for use with tungsten filament, tubular fluorescent and other discharge lamps on supply voltages not exceeding 1 000 V. It is to be read in conjunction with those sections of Part 1 to which reference is made.
Document Number:
NL IEC 60598 2 2 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
25000.0000
This part of IEC 60598 specifies requirements for recessed luminaires incorporating electric light sources for operation from supply voltages up to 1 000 V. This section does not apply to air-handling or liquid-cooled luminaires
Document Number:
NL IEC 60598 2 3 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
35000.0000
This part of IEC 60598 specifies requirements for − luminaires for road, street lighting and other public outdoor lighting applications; − tunnel lighting; − column-integrated luminaires with a minimum total height above normal ground level of 2,5 m; and for use with electrical lighting sources on supply voltages not exceeding 1 000 V. NOTE Column integrated luminaires with a total height below 2,5 m are under consideration
Document Number:
NL IEC 60598 2 4 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
25000.0000
This part of IEC 60598-2 specifies requirements for portable general purpose luminaires for indoor and/or outdoor use (e.g. garden use), other than handlamps designed to be used with or incorporating electrical light sources on supply voltages not exceeding 250 V
Document Number:
NL IEC 60598 2 5 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
25000.0000
This part of IEC 60598 specifies requirements for floodlights for use with electrical light sources on supply voltages not exceeding 1 000 V
Document Number:
NL IEC 60598 2 6 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
35000.0000
This section of IEC 598-2 specifies requirements for luminaire with built-in transformers for filament lamps, with supply voltages and output voltages not exceeding: - 1 000 V for class I and class li luminaires and - 250 V for class 0 luminaires. It is to be read in conjunction with those sections of IEC 598-1 to which reference is made. This section does not apply to class Ill luminaires. It is not necessary to use "Safety extra low voltage" (SELV) transformers to comply with the requirements of this section. However, such transformers may satisfy the functional requirements of this section.
Document Number:
NL IEC 60598 2 7 : 2007
Sector:
Electrical Engineering
Status:
C
Production Year:
2007
Price:
35000.0000
This section of Part 2 of I EC Publication 598 specifies requirements for po rtable pedestal luminaires for use in places such as gardens and for portable luminaires for use in places such as flower beds, for use with tungsten filament, tubular fluorescent and other discharge lamps on supply voltages not exceeding 250 V. It is to be read in conjunction with those sections of Pa rt 1 to which reference is made.
Document Number:
NL NF P 1 12 : 2007
Sector:
Construction Materials and Building
Status:
C
Production Year:
2007
Price:
35000.0000
La présente norme s'applique aux garde-corps et aux rampes d'escalier de caractère définitif rencontrés dans : - les bâtiments - d'habitation, - de bureaux, - commerciaux, - scolaires, - industriels et agricoles (pour les locaux où le public a accès), ainsi qu'aux abords de ces bâtiments, - les autres établissements recevant du public et leurs abords. La présente norme ne vise pas : - les garde-corps et rampes situés à l'intérieur des logements et ne donnant pas sur l'extérieur, si le maître de l'ouvrage le notifie, - les garde-corps, rampes et éléments de sécurité situés sur les toitures ou dans les locaux, passages et emplacements techniques réservés au personnel d'exploitation ou d'entretien, ni les garde-corps d'échafaudages de caractère provisoire, - les balcons de salles de théâtre, salles de cinéma et autres lieux de spectacles si le maître d'ouvrage le notifie, - les tribunes de stades, si le maître d'ouvrage le notifie. Dans tous les cas la norme vise les escaliers desservant
Document Number:
NL NF P 1 13 : 2007
Sector:
Construction Materials and Building
Status:
C
Production Year:
2007
Price:
25000.0000
La présente norme s'applique aux garde-corps de bâtiments définis parla norme NF PO 1-012. Elle concerne le comportement intrinsèque des garde-corps rectilignes à l'exclusion de leur fixation à la structure. Les essais tels que définis ci-après suffisent à justifier ce comportement. Pour que les essais des garde-corps métalliques soient représentatifs, il faut que les caractéristiques mécaniques, (limite élastique, rupture et allongement) du matériau utilisé pour l'essai, soient connues et que la limite élastique ne dépasse pas de plus de 30 % la limite élastique garantie. Essais statiques : ils sont réalisés pour les seuls types de garde-corps qui ne sont pas justifiés ou que l'on ne sait pas justifier par le calcul. Essais dynamiques : ils sont réalisés pour tous les types de garde-corps. Ils ne sont effectués que si le système d'assemblage du remplissage ou du barreaudage n'est pas éprouvé par des essais ou des références antérieures. La présente norme ne s'applique pas : - aux garde-corps à usage industriel définis dans la norme NF E 85-101, - aux garde-corps consacrés aux ouvrages d'art qui répondent aux exigences requises par le fascicule 61 titre II du Ministère de l'Urbanisme et du Logement et du Ministère des Transports.