Libnor | المعايير |

Document Number: NL ISO 9346 : 2003

This International Standard defines physical quantities and other terms in the field of thermal insulation relating to heat transfer by radiation.

Thermal insulation - Mass transfer - Physical quantities and definitions

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 31 : 2003

This International Standard defines physical quantities and other terms in the field of mass transfer relevant to buildings, building elements and systems, building components and building materials. For physical quantities the standard also gives the corresponding symbols and units.

Pedestal wash basins - connecting dimensions

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 33 : 2003

This European Standard specifies the connecting dimensions of wash basins in accordance with EN 14688 regardless of materials used for their manufacture. NOTE 1 Other connecting dimensions are permitted, e.g. special designs of wash basins, if the manufacturer supplies or recommends the appropriate fitting. NOTE 2 The shape of the appliance in the figures is for illustration only; it in no way prejudices the final shape of the appliance, which is left to the initiative of the manufacturer.

Pedestal WC pans with close-coupled flushing cistern - Connecting dimensions

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 34 : 2003

la presentte norme specifie les caracteristiques de raccordement des cuvettes de W.C. sur pied, a chasse directe, a reservoir attenant, a sortie apparente d axe horizontal ou vertical ou a sortie cache, quells que soient les materiaux entrant dans leur fabrication. Elle n’a pas trait aux cuvettes a aspiration siphonique. NOTE: seules les dimensions des parties cotees doivent etre respectees . la forme schematique des appareils representee dans les figures pas des traits fins est donnee pour faciliter la comprehension elle ne prejudge en rien de la form definitive de l appareil qui laisse a l initative des fabricants.

Wall-hung hand rinse basins - Connecting dimensions

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 35 : 2003

la presente norme a pour object de fixer les caracteristiques de raccordement des cuvettes de WC suspendues a chasse directe et reservoir attenat, quells que soient les materiaux entrant dans eur fabrication. Elle n a pas trait aux cuvettes a aspiration siphonique. NOTE: seules les dimensions des parties cotees doivent etre respectees . la forme schematique des appareils representee en trait tirete sur la croquis est donnee pour une meilleur comprehension des dessin ; elle ne prejige en rien la form definitive des appareils qui est laisse a l initiative des fabricants.

Pedestal bidets with over-rim supply - Connecting dimensions

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 36 : 2003

la presentte norme a pour objet de fixer lles caracteristiques de raccordement des bidets sur pied a alimentation par surverse, independamment du materiau don’t ils sont faits. NOTE: seules les dimensions des parties cotees doivent etre respectees. la form schematique des appareils representes dans les figures est donnee uniquement pour faciliterla comprehension, ellle ne prejudge enrien de la form definitive de l appareil qui esr laisse a l initative des fabricants.

Wall-hung bidets with over-rim supply- connecting dimensions

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 293 : 2003

La presente norme specifie les caracteristiques de raccordement des bidets suspendus a alimentation par surverse, quells que soient les materiaux entrant dans leur fabrication. NOTE seules les dimensions des parties cotees doivent etre respectees, la forme schematique desappareils representee dans les figures est donnee uniquemenet pour faciliter la comprehension; elle ne prejudge en rien de la form definitive de l appareil qui est laisse a l initative des fabricants.

Oil pressure atomizing nozzles -Minimum requirements -Testing

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 299 : 2003

This European standards applies to oil pressure atomizing nozzles without backflow - herein called atomizing nozzles - with a nominal throughout <= 6,30 kg/h at 10 bar with a fuel oil. They are characterized by the requirements concerning the operational function according to clause 5.

Oil pressure atomizing nozzles - Determination of the angle and spray

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 546 3 : 2003

This European Standard specifies a method for the determination of the spray characteristic and the index angle of oil pressure atomizing nozzles.

Aluminium and Aluminum Alloys foil - Part 3: Tolerances and dimentions

Document Number: NL EN 546 4 : 2003

This document specifies the tolerances on dimensions for single and double-rolled aluminium and aluminium alloy foil supplied in accordance with EN 546-1

Aluminium and Aluminum Alloys foil - Part 4: Special Property Requirements

Document Number: NL 525 : 2003

This document specifies the requirements for special properties of wrought aluminium and wrought aluminium alloy foil and their tests. It applies to flat rolled products. It does not apply to lacquered, painted, embossed or laminated products. The technical conditions for inspection and delivery of foil are specified in EN 546-1.

Woven dress suit fabrics composed of blended wool fibers

Document Number: NL 526 : 2003

تحدد هذه المواصفة القياسية القماش المنسوج من خيوط مخلوطة 55 % عديد الإستر و45 % صوف

Woven dress suit fabrics composed of blended cotton fibers

Document Number: NL 527 : 2003

تختص هذه المواصفة القياسية بالقماش المنسوج من خيوط مخلوطة من ألياف عديد الإستر وألياف القطن بنسب مختلفة والمجهز لصناعة الملابس الخارجية.

Specification for woven centain (out door) and tents

Document Number: NL 528 : 2003

تحدد هذه المواصفة القياسية اللبنانية أهم ميزات المواد للأقمشة المنسوجة من أجل الشوادر والخيم* ويمكن تطبيقها أيضاً على أنماط أخرى من الأقمشة. لملاقاة الاحتياجات الناتجة عن مختلف الظروف المناخية ومختلف العادات المحلية في استعمال الخيم ومختلف توقعات الزبون حول مدة التحمل. تنقسم متطلبات المواد إلى درجتين (A) و (B). تطبق متطلبات الدرجة (A) على أقمشة الشوادر والخيم الملحوظة للاستعمال القاسي و/أو الطويل الأمد. أما متطلبات الدرجة (B) فهي أدنى من الدجة (A) وهي تطبق على الأقمشة الملحوظة للاستعمال الأقل قسوة

Specification for bath towel fabrics

Document Number: NL 655 : 2003

تحدد هذه المواصفة القياسية المتطلبات الواجب توافرها في المناشف القطنية الوبرية المصنعة من القطن بنسبة (100) % لخيط الوبرة

Sweeteners Permitted in Food Products

Document Number: NL EN 12430 : 2003

تحدد هذه المواصفة القياسية المحليات المسموح باستعمالها لإضفاء طعم حلو للمنتجات الغذائية وأو المقدمة على المائدة للتحلية (Table-top sweeteners). لا تطبق هذه المواصفة القياسية على الأغذية التي لها خصائص ذاتية محلية

Thermal insulating products for building applications - Determination of behaviour under point load

Sector: Mechanical Systems and Components for General Use

Document Number: NL 659 : 2003

This European Standard specifies equipment and procedures for determining the behaviour of products under a force applied to a small area of a test specimen at a given speed. It is applicable to thermal insulating products. This European Standard can be used to determine whether the products have sufficient strength to withstand forces applied directly to them either during installation or during application, mainly caused by pedestrian traffic. NOTE The test methods given in the main body of the standard and in Annex A are reported and interpreted in different ways. The similarities that exist between the methods are not sufficient to permit reasonable comparisons to be made.

General Principles for the Addition of Essential Nutrients to foods

Document Number: NL 661 : 2003

تهدف هذه المواصفة القياسية إلى تحديد المتطلبات والشروط الواجب توافرها في جميع الأغذية التي أضيفت إليها عناصر تغذوية أساسية، والمعدة للاستهلاك المباشر

Guidelines for Use of Nutrition Claims

Document Number: NL 653 : 2003

تطبق التوجيهات الواردة في هذه المواصفة القياسية، على كافة المنتجات التي تحوي بيانات إدعائية تغذوية، دون الإخلال بالاشتراطات الخاصة الواردة في إطار المواصفات والتوجيهات المتعلقة بأغذية الحمية والأغذية المعدة لأغراض طبية خاصة. تهدف هذه المواصفة القياسية إلى استكمال "التوجيهات العامة لاستعمال البيانات الادعائية"، ولا تحل بدل أي من التحظيرات الواردة فيها.

Frozen Artichokes

Document Number: NL IEC 60947 5 1 : 2003

تهدف هذه المواصفة القياسية إلى تحديد المتطلبات والشروط الواجب توافرها في الأرضي شوكي المجمّدة المعدة للاستهلاك المباشر دون تصنيع إضافي، فيما عدا التصنيف أو إعادة التعبئة. لا تشمل هذه المواصفة القياسية المنتجات التي ستخضع لأي تصنيع إضافي، أو المعدة لأغراض صناعية أخرى

Low-voltage switchgear and controlgear- Part 5: Control circuit devices and switching elements - Section 1: Electromechanical control circuit devices

Document Number: NL EN 12431 : 2003

IEC 60947-5-1:2016 RLV contains both the official IEC International Standard and its Redline version. The Redline version is not an official document, it is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition. IEC 60947-5-1:2016 applies to control circuit devices and switching elements intended for controlling, signalling, interlocking, etc., of switchgear and controlgear. It applies to control circuit devices having a rated voltage not exceeding 1 000 V a.c. (at a frequency not exceeding 1 000 Hz) or 600 V d.c. This fourth edition cancels and replaces the third edition published in 2003 and its Amendment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) update of normative references; b) update and restructuration of subclauses in 7.1; c) addition of material requirements and test; d) udpate of EMC requirements; e) clarification of requirements and update of 8.2; f) addition of requirements for screwless-type clamping units; g) udpate of existing Tables 4 and 5; h) addition of new Tables 6, 7, 8 and 9; i) addition of a new Figure 10 ; j) addition of a new Annex N. This publication is to be read in conjunction with IEC 60947-1:2007.

Thermal insulating products for building applications - Determination of thickness for floating floor insulating products

Sector: Mechanical Systems and Components for General Use

Document Number: NL IEC 61082 1 : 2003

This European Standard specifies the equipment and procedures for determining the thickness of thermal insulating products for impact sound insulation in floating floor applications.

Preparation of documents used in electrotechnology-Part 1: General requirements

Document Number: NL IEC 61082 2 : 2003

IEC 61082-1:2014 is available as IEC 61082-1:2014 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61082-1:2014 establishes general rules and guidelines for the presentation of information in documents, and specific rules for diagrams, drawings and tables used in electrotechnology. This third edition cancels and replaces the second edition published in 2006. It constitutes a technical revision and includes the following changes: - inclusion of presentation rules for wireless interconnections; - description of exceptional cases for the application of rules for positioning of reference designations in diagrams; - correction of errors and update of the normative references; - harmonization of definitions with respect to referenced publications. This horizontal standard is primarily intended for use by technical committees in the preparation of standards in accordance with IEC Guide 108

Preparation of documents used in electrotechnology-Part 2: function-orientaded diagrams

Document Number: NL IEC 61082 3 : 2003

Provides rules for function oriented diagrams. Coverage includes: location reference systems; representation of supply circuits; representation of combined electrical and non electrical circuits; representation of binary logic circuits; terminals connected to internal branches; overview diagrams for control systems for non electrical processes; contents of a function diagram; contents of a circuit diagram; symbols with a large number of terminals.

Preparation of documents used in electrotechnology- Part 3: Connection diagrams, tables and lists

Document Number: NL IEC 61082 4 : 2003

This standard contains definitions and general information applicable to most of the commonly used Electrical and Electronics Diagrams. It also includes detailed recommendations on preferred practices for use in the preparation of Electrical and Electronics Diagrams. The recommended practices covered by this standard are ground rules designed to eliminate divergent Electrical and Electronics Diagram drafting techniques. The illustrations shown represent good drafting practices. They are not intended as engineering design guides

Preparation of documents used in electrotechnology- Part 4: Location and installation documents

Document Number: NL IEC 61095 : 2003

Provides rules for location and installation documents mainly used for installation work. Covers different systems and objects such as arrangements or installation drawings for site, buildings and equipment, installation drawings or diagrams for site or buildings and drawings for location on or in components.

Electromechanical contactors for household and similar purposes

Document Number: NL EN 12241 : 2003

This International Standard applies to electromechanical air break contactors for household and similar purposes provided with main contacts intended to be connected to circuits the rated voltage of which does not exceed 440 V a.c. with rated operational currents less than or equal to 63 A for utilization category AC-7a and 32 A for utilization category AC-7b, and rated conditional short-circuit current less than or equal to 6 kA. The contactors dealt with in this standard are not normally designed to interrupt short-circuit currents. Therefore, suitable short-circuit protection (see 9.3.4) shall form part of the installation. This standard does not apply to: contactors complying with IEC 60947-4-1; semiconductor contactors; contactors designed for special applications; auxiliary contacts of contactors. These are dealt with in IEC 60947-5-1. This standard states: 1) The characteristics of contactors. 2) The conditions with which contactors shall comply with reference to: a) their operation and behaviour; b) their dielectric properties; c) the degrees of protection provided by their enclosures, where applicable; d) their construction; e) their electromagnetic compatibility characteristics. 3) The tests intended for confirming that these conditions have been met, and the methods to be adopted for these tests. 4) The test sequences and the number of samples to be submitted for certification purpose. 5) The information to be given with contactors or in the manufacturer’s literature

Thermal insulation for building equipment and industrial installations - Calculation rules

Sector: Mechanical Systems and Components for General Use

Document Number: NL IEC 60998 2 1 : 2003

This International Standard gives rules for the calculation of heat transfer properties of building equipment and industrial installation, predominantly under steady-state conditions, assuming one-dimensional heat flow only.

Connecting devices for low voltage circuits for household and similar purposes- Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units.

Document Number: NL IEC 60998 2 2 : 2003

This standard applies to connecting devices with screw-type clamping units primarily suitable for connecting unprepared conductors. This Part 2-1 is intended to be used in conjunction with IEC 60998-1. It was established on the basis of the second edition (2002) of that standard. This second edition cancels and replaces the first edition published in 1990 and constitutes a technical revision

Connecting devices for low voltage circuits for household and similar purposes- Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units.

Document Number: NL IEC 60998 2 3 : 2003

This standard applies to connecting devices with screwless-type clamping units primarily suitable for connecting unprepared conductors. This Part 2-1 is intended to be used in conjunction with IEC 60998-1. It was established on the basis of the second edition (2002) of that standard. This second edition cancels and replaces the first edition published in 1991 and constitutes a technical revision.

Connecting devices for low voltage circuits for household and similar purposes- Part 2-3: Particular requirements for connecting devices as separate entities with insulation piercing clamping units.

Document Number: NL IEC 60998 2 4 : 2003

This standard applies to connecting devices with insulation piercing clamping units primarily suitable for connecting insulated unprepared conductors. In the connecting operation the insulation of the conductor is pierced, bored through, cut through, removed, displaced or made ineffective in some other manner at the point or points of contact. This Part 2-1 is intended to be used in conjunction with IEC 60998-1. It was established on the basis of the second edition (2002) of that standard. This second edition cancels and replaces the first edition published in 1991 and constitutes a technical revision. The contents of the corrigendum of November 2006 have been included in this copy.

Connecting devices for low voltage circuits for household and similar purposes- Part 2-4: Particular requirements for twist-on connecting devices.

Document Number: NL IEC 60947 4 1 A1 : 2003

This International Standard applies to twist-on connecting devices for connecting two or more unprepared rigid and/or flexible copper conductors having a cross-sectional area of 0,5 mm2 up to and including 16 mm2 and complying with IEC 60228, the total cross-sectional area of the connected conductors not exceeding 35 mm2. It covers low voltage circuits up to 1 000 V a.c. and 1 500 V d.c. where electrical energy is utilized for household and similar purposes

Low-voltage switchgear and controlgear- Part 4 : Contactors and motor starters -Section 1:Electromechanical contactors and motor-starters - Amendment 1

Document Number: NL IEC 60947 5 1 A1 : 2003

IEC 60947-4-1:2018 RLV contains both the official IEC International Standard and its Redline version. The Redline version is not an official document, it is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition. IEC 60947-4-1:2018 is applicable to the following equipment: - electromechanical contactors and starters including motor protective switching device (MPSD); - actuators of contactor relays; - contacts dedicated exclusively to the coil circuit of this contactor or this contactor relay; - dedicated accessories (e.g. dedicated wiring, dedicated latch accessory); intended to be connected to distribution circuits, motors circuits and other load circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC. This fourth edition cancels and replaces the third edition published in 2009 and its Amendment 1:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - Scope structure and exclusions - Editorial correction of notes and hanging paragraphs - Reference to IEC 62683-1 - Motor protective switching device (MPSD) with its requirements - Safety aspects related to: - General aspects; - Limited energy circuits; - Electronic circuits; - Assessment procedure for electromechanical overload protection used in safety -applications (new Annex L) - Introduction of provisions covering the impact of higher locked rotor current to achieve high efficiency class - Mention of dedicated wiring accessories - Pickup power measurement - Alignment to IEC 60947-1:2007, IEC 60947-1:2007/AMD1:2010, and IEC 60947‑1:2007/AMD2:2014 - Direct current requirements for covering photovoltaic application (new Annex M) - Load monitoring indicators (new Annex O) - Short-circuit breaking tests of MPSD (new Annex P) - Co-ordination under short-circuit conditions between a MPSD and another short-circuit protective device associated in the same circuit (new Annex Q).

Low-voltage switchgear and controlgear- Part 5: Control circuit devices and switching elements - Section 1: Electromechanical control circuit devices - Amendment 1

Document Number: NL IEC 60947 6 1 A1 : 2003

Low-voltage switchgear and controlgear- Part 6: Multiple function equipment - Section 1: Automatic transfer switching equipment - Amendment 1

Document Number: NL IEC 60947 3 : 2003

IEC 60947-6-1:2005+A1:2013 applies to transfer switching equipment (TSE) to be used in power systems with interruption of the supply to the load during transfer, the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c. This consolidated version consists of the second edition (2005) and its amendment 1 (2013). Therefore, no need to order amendment in addition to this publication. This publication is to be read in conjunction with IEC 60947-1:2007.

Low-voltage switchgear and controlgear- Part 3: Switches,disconnectors,switch-disconnectors and fuse-combination units

Document Number: NL EN 226 : 2003

IEC 60947-3:2008+A1:2012+A2:2015 applies to switches, disconnectors, switch-disconnectors and fuse-combination units to be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1 000 V a.c. or 1 500 V d.c. The manufacturer shall specify the type, ratings and characteristics according to the relevant standard of any incorporated fuses. The technical content is therefore identical to the base edition and its amendment and has been prepared for user convenience. A vertical line in the margin shows where the base publication has been modified by amendment 1. Additions and deletions are displayed in red, with deletions being struck through. The contents of the corrigenda of September 2012 and of November 2013 have been included in this copy. This consolidated version consists of the third edition (2008), its amendment 1 (2012) and its amendment 2 (2015). Therefore, no need to order amendments in addition to this publication. This publication is to be read in conjunction with IEC 60947-1:2011.

Atomizing Oil Burners : Connecting Dimensions Between Burners and Heat Generatorss

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 247 : 2003

appareil de chauffage brûleur à mazout brûleur pulvérisation générateur d'air chaud classification liaison mécanique fixation dimension tolérance de dimension.

Heat exchangers - Terminology

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 248 : 2003

The scope of this European Standard is to establish heat exchanger terminology so that consistent terms are used. For the purposes of this European Standard a heat exchanger is a device, the main function of which is to transfer heat between two fluids, with physical separation by a wall. Heat exchange between a fluid and a solid material (in the case of ovens in particular) is therefore excluded.

Sanitary tapware - General technical specifications for electrodeposited Nickel Chrome coatings

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 246 : 2003

The aim of this European Standard is: - to define the condition of the exposed surfaces of tapware, - to establish the characteristics (resistance to corrosion, adherence) of the surface coating, - to describe the tests for verifying these characteristics. It applies to all sanitary fittings (supply or waste fittings) which have a metallic Ni-Cr coating, whatever the nature of the substrate material.

Sanitary tapware - General specifications for flow rate regulators

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 251 : 2003

This European Standard specifies the performance criteria related to the health and environmental protection of people for sanitary taps and their related accessories used for the water supply. The performance requirements are expressed in terms of mechanical endurance, flow rate, effectiveness and level of acoustic pressure. This standard includes and makes reference to the corresponding test methods and the evaluation of conformity of the product to this standard

Shower trays - Connecting dimensions

Sector: Mechanical Systems and Components for General Use

Document Number: NL EN 546 1 : 2003

This European Standard specifies requirements for the connecting dimensions for shower trays, regardless of the material used for their manufacture. This European Standard applies to shower trays used for domestic purposes and complements the standards for shower trays made from different materials, the existing standard on waste fittings (EN 274-1) in terms of their dimensional requirements. NOTE Only dimensions are compulsory. The shape of the appliance in the figures is for illustration only; it in no way prejudices the shape of the appliance which is left to the initiative of the manufacturer.

Aluminium and aluminium alloys Foil – Part 1: Technical conditions for inspections and delivery

Document Number: NL EN 546 2 : 2003

This document specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy foil. The gauge range covered is 6 m to 200 m. It does not apply to lacquered, painted, embossed or laminated products.

Aluminium and Aluminum Alloys foil - Part 2: Mechanical properties

Document Number: NL 523 : 2003

This document specifies the mechanical properties of wrought aluminium and aluminium alloy foil. The chemical composition limits of these materials are specified in EN 573-3. The designations of aluminium and aluminium alloys and the temper designations used in this standard are specified in EN 573-3 and the temper designation are defined EN 515.

Textiles - Mixtures of cotton (50%) and polyester (50%) fibers for military uniforms

Document Number: NL 524 : 2003

تحدد هذه المواصفة القياسية الحد الأدنى للمتطلبات خصائص الأقمشة الممزوجة قطن (50 %) وبوليستر (50 % ) المصبوغة و/أو المطبعة حسب الرسمة الموضوعة من قبل الجهات المعنية والمخصصة لبدلات العمل العسكرية.

Knitted fabrics for dress suit composed of blended cotton fibres

Document Number: NL 451 : 2003

تحدد هذه المواصفة القياسية خصائص الأداء للأقمشة المنسوجة للبدلات وللسراويل والستر (الجاكيتات) الرجالية والولادية من أي نوع كانت الألياف النسيجية أو المزيج المكونة لها وللأقمشة ذات الكتل الوزنية بالمتر المربع المختلفة. ولا تشير هذه المواصفة القياسية إلى أقمشة البطانات.

Adult Diapers

Sector: Paper Technology

Document Number: NL 452 : 2003

تحدد هذه المواصفة القياسية الاشتراطات الواجب توفرها في الحفائض الجاهزة للبالغين للاستعمال لمرة واحدة

Female sanitary napkins

Sector: Paper Technology

Document Number: NL 640 : 2003

تحدد هذه المواصفة القياسية الاشتراطات الواجب توفرها في الفوط الصحية النسائية للاستعمال لمرة واحدة.

Canned Pears

Document Number: NL 639 : 2003

تهدف هذه المواصفة القياسية إلى تحديد المتطلبات والشروط الواجب توافرها في الأجاص المعلّب

Canned Pineapple

Document Number: NL 631 : 2003

تهدف هذه المواصفة القياسية إلى تحديد المتطلبات والشروط الواجب توافرها في الأناناس المعلّب

Carrots